There may be an open circuit in the CAN main wire and/or DLC3 branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher. | ·
CAN main wire or connector ·
No. 1 junction connector ·
No. 2 junction connector ·
ECM ·
Combination meter assembly ·
DLC3 branch wire or connector |
Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F4-6 (CANH) - F4-14 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of DLC3 |
When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)>HOW TO PROCEED WITH TROUBLESHOOTING) after repairing the trouble area.
OK
NG
Disconnect the F83 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-10 (CANH) - F83-21 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
OK
NG
Reconnect the F83 No. 2 junction connector.
NEXT
Disconnect the F1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F1-32 (CANH) - F1-31 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
OK
NG
Reconnect the F1 combination meter assembly connector.
NEXT
Disconnect the F83 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F83-7 (CANH) - F83-18 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
OK
NG
Reconnect the F83 No. 2 junction connector.
NEXT
Disconnect the A74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A74-41 (CANH) - A74-49 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (1NZ-FE) | B |
| OK (2NZ-FE) | C |
A
B
C
Reconnect the A74 ECM connector.
NEXT
Disconnect the A61 and F82 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A61-9 (CANH) - A61-20 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F82-4 (CANH) - F82-15 (CANL) | Ignition switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
OK
NG