Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.08–2014.07
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248286 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U158579E02
0.167,0.052 0.417,0.302 0.25,0.25 10 false *a 1.25,6.698 1.5,6.948 0.25,0.25 10 false *b 0.406,2.146 0.594,2.323 0.188,0.177 10 false 3E 0.948,2.146 1.125,2.323 0.177,0.177 10 false 3F 6.479,1.542 6.729,1.792 0.25,0.25 10 false 3A 6.49,0.938 6.74,1.167 0.25,0.229 10 false 3B 0.938,1.542 1.135,1.75 0.198,0.208 10 false 3C 0.938,0.938 1.188,1.167 0.25,0.229 10 false 3D 0.938,2.385 1.188,2.635 0.25,0.25 10 false *B 0.406,2.385 0.656,2.635 0.25,0.25 10 false *A 5.802,3.698 5.99,3.875 0.188,0.177 10 false 3E 6.354,3.698 6.531,3.875 0.177,0.177 10 false 3F 6.344,3.927 6.594,4.115 0.25,0.188 10 false *B 5.813,3.927 6.063,4.115 0.25,0.188 10 false *A 3.792,2.896 4.156,3.135 0.365,0.24 10 false MB 3.792,0.813 4.052,1.073 0.26,0.26 10 false MB 4,3.875 4.198,4.052 0.198,0.177 10 false 3C 1.521,3.875 1.719,4.052 0.198,0.177 10 false 3D 5.51,5.24 5.698,5.417 0.188,0.177 10 false 3A 1.635,5.24 1.823,5.417 0.188,0.177 10 false 3B 3.792,6.49 4.052,6.667 0.26,0.177 10 false F76 3.698,7.563 3.958,7.74 0.26,0.177 10 false F76

Text in Illustration
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
*b Component without harness connected
(Main Body ECU (Multiplex Network Body ECU))

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
MB-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω
MB-29 (ACC) - Body ground None - Body ground Battery power supply Ignition switch ACC 11 to 14 V
MB-30 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
MB-32 (IG) - Body ground None - Body ground Battery power supply Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU) onto the instrument panel junction block assembly.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
3B-12(LIN2) - 3B-8 (GND1) W - W-B LIN Communication line Ignition switch ON Pulse generation

If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Driver Side) (for LHD)


U127175E03
3.469,0.271 3.688,0.427 0.219,0.156 10 false H3

a.

Disconnect the H3 power window regulator motor assembly LH (for driver side) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
H3-2 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Driver Side) (for RHD)


U127174E02
3.458,0.281 3.719,0.448 0.26,0.167 10 false G3

a.

Disconnect the G3 power window regulator motor assembly RH (for driver side) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G3-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G3-2 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.