Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › 2011.08–2014.07
RM19S0E _57 Power Source / Network _051488 POWER DISTRIBUTION _0248284 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  REMOVAL  


PROCEDURE

Hide 55302A 1.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY (for LHD)

Hide 55433B 2.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (for LHD)

Hide 55550 3.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for RHD)

Hide 82141 4.SEPARATE INSTRUMENT PANEL WIRE

a.
B264801

Remove the screw.


b.

Disengage the clamp and remove the instrument panel wire.


Hide 82730 5.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
B264800

Disengage the clamps.


b.

Disconnect the connectors on the front side of the instrument panel junction block.


c.

Disconnect the main body ECU connector.


d.
E219258

Remove the 2 bolts.


e.
E219260

Disengage the claw and 2 clamps and separate the instrument panel junction block.


f.
B264803E01
2.384,1.513 2.540,1.694 0.156,0.181 10 A

Disconnect the back side connector A indicated as shown in the illustration.


g.
B272142E04
0.458,0.49 0.75,0.927 false 1.417,1.125 1.573,1.302 0.156,0.177 10 false B 0.271,0.302 0.427,0.479 0.156,0.177 10 false *a

Slide the lever to the upward.

Text in Illustration
*a Lever


h.

Disconnect the back side connector B indicated as shown in the illustration.


i.

Remove the instrument panel junction block.


Hide 6.REMOVE JUNCTION BLOCK BRACKET

a.
B266611E01
1.305,1.6 1.007,1.7 false 0.811,1.652 0.967,1.833 0.156,0.181 10 *1

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the junction block bracket.

Text in Illustration
*1 Protective Tape


Hide 7.REMOVE JUNCTION BLOCK BRACKET

a.
E219259E01
1.112,0.4 1.297,0.572 0.185,0.172 10 *1 1.655,0.616 1.304,0.497 false

Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the junction block bracket.

Text in Illustration
*1 Protective Tape


Hide 89221 8.REMOVE MAIN BODY ECU

a.
E184411E02
2.334,1.529 2.935,1.488 false 0.317,1.573 0.283,1.882 false 0.447,1.58 0.721,1.874 false 0.256,1.894 0.412,2.075 0.156,0.181 10 *2 0.66,1.895 0.816,2.076 0.156,0.181 10 *3 2.959,1.396 3.115,1.578 0.156,0.181 10 *1

Release the lock on the junction block side.

Text in Illustration
*1 Protective Tape
*2 Main Body ECU
*3 Instrument Panel Junction Block


b.

While pressing the lock on the junction block side, insert a screwdriver with its tip wrapped in protective tape between the main body ECU and the junction block.

NOTICE:

Use a thin-blade screwdriver with a diameter of 5.0 to 6.3 mm (0.197 to 0.248 in.), and with a length of 90 mm or more.



c.
E184412E02
0.813,1.424 1.025,1.605 0.213,0.181 10 *1 0.532,1.076 0.766,1.437 false 2.072,1.791 2.284,1.972 0.213,0.181 10 *1 2.5,1.509 2.266,1.871 false

Do not pry the inserted screwdriver. Lift up the main body ECU to the point where the lock releases.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Do not twist the screwdriver to raise the main body ECU.

·

If any terminals of the connectors, locking parts or cases are deformed or damaged, replace the instrument panel junction block assembly or the main body ECU.




d.
E184413

Remove the main body ECU by pulling it out from the junction block.

NOTICE:

Do not touch the main body ECU connector.