Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2011.08–2014.07
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248286 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2325 Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row.
·

Power window regulator motor assembly RH (for driver side)*1

·

Power window regulator motor assembly LH (for driver side)*2

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Harness or connector



*1: for RHD

*2: for LHD


WIRING DIAGRAM

E214075E08
5.302,0.563 5.74,0.729 0.438,0.167 10 false DOOR 0.198,2.01 2.875,2.323 2.677,0.313 10 false Instrument Panel Junction Block Assembly 0.229,0.99 0.531,1.156 0.302,0.167 10 false MB 1.469,0.406 1.771,0.573 0.302,0.167 10 false 16 4.854,0.833 5.156,1 0.302,0.167 10 false 1 4.854,0.292 5.156,0.458 0.302,0.167 10 false 2 4.667,0.375 4.969,0.542 0.302,0.167 10 false B 4.458,0.948 4.833,1.115 0.375,0.167 10 false GND 6.219,0.375 7.156,0.688 0.938,0.313 10 false from ALT Fuse 0.229,1.167 2.208,1.802 1.979,0.635 10 false Main Body ECU (Multiplex Network Body ECU) 0.615,2.469 2.323,2.75 1.708,0.281 10 false : LIN Communication Line 1.052,0.615 1.375,0.781 0.323,0.167 10 false LIN2 3.917,0.604 4.24,0.802 0.323,0.198 10 false LIN2 3.375,1.5 5.5,2.135 2.125,0.635 10 false Power Window Regulator Motor Assembly RH (for Driver Side)*1 3.375,2.146 5.479,2.781 2.104,0.635 10 false Power Window Regulator Motor Assembly LH (for Driver Side)*2 2.604,0.479 2.906,0.646 0.302,0.167 10 false 12 0.188,1.833 0.49,2 0.302,0.167 10 false 3B 3.719,0.49 4.021,0.656 0.302,0.167 10 false 9 3.365,1.333 3.708,1.5 0.344,0.167 10 false G3 3.375,1.969 3.719,2.135 0.344,0.167 10 false H3 6.333,2.083 7.115,2.406 0.781,0.323 10 false *1 : for RHD 6.333,2.417 7.094,2.74 0.76,0.323 10 false *2 : for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When using the intelligent tester to troubleshoot with the ignition switch off:

Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B


A

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
U158663E02
1.667,2.573 1.406,2.906 false 0.125,0.104 0.427,0.375 0.302,0.271 10 false *a 1.271,2.917 1.604,3.188 0.333,0.271 10 false LIN2 1.646,2.083 1.875,2.26 0.229,0.177 10 false MB 1.667,0.229 1.854,0.406 0.188,0.177 10 false 3B

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the 3B instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-12 - MB-16 (LIN2) Always Below 1 Ω
3B-12 or MB-16 (LIN2) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY)
a.

Disconnect the G3 power window regulator motor assembly RH (for driver side)*1 or H3 power window regulator motor assembly LH (for driver side)*2 connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-12 - G3-9 (LIN)*1
3B-12 - H3-9 (LIN)*2
Always Below 1 Ω
3B-12 or G3-9 (LIN) - Body ground*1
3B-12 or H3-9 (LIN) - Body ground*2
Always 10 kΩ or higher



*1: for RHD

*2: for LHD



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U126577E03
1.51,1.031 1.198,1.354 true 2.26,1.375 1.938,1.052 true 0.24,0.583 0.531,0.74 0.292,0.156 10 false G3 0.833,0.563 1.125,0.719 0.292,0.156 10 false *a 0.833,0.979 1.125,1.135 0.292,0.156 10 false *b 0.875,1.313 1.219,1.469 0.344,0.156 10 false GND 2.302,1.323 2.646,1.479 0.344,0.156 10 false B 0.271,0.99 0.563,1.146 0.292,0.156 10 false H3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-1 (GND) - Body ground*1
H3-1 (GND) - Body ground*2
Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G3-2 (B) - Body ground*1
H3-2 (B) - Body ground*2
Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Power Window Regulator Motor Assembly RH (for Driver Side))
*a Front view of wire harness connector
(to Power Window Regulator Motor Assembly LH (for Driver Side))


*1: for RHD

*2: for LHD



A

6.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Replace the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).

*1: for RHD

*2: for LHD




NEXT

7.CLEAR DTC
7.CLEAR DTC

NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

END (POWER WINDOW REGULATOR MOTOR WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)