The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects errors in communication with all the ECUs connected to the door bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be stored.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2325 | Main body ECU (multiplex network body ECU) detects errors in communication with the ECUs connected to the door bus lines 3 times in a row. | ·
Power window regulator motor assembly RH (for driver side)*1 ·
Power window regulator motor assembly LH (for driver side)*2 ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Harness or connector |
*1: for RHD
*2: for LHD
When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
When using the intelligent tester to troubleshoot with the ignition switch off:
Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-12 - MB-16 (LIN2) | Always | Below 1 Ω |
| 3B-12 or MB-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG
Disconnect the G3 power window regulator motor assembly RH (for driver side)*1 or H3 power window regulator motor assembly LH (for driver side)*2 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-12 - G3-9 (LIN)*1
3B-12 - H3-9 (LIN)*2 |
Always | Below 1 Ω |
| 3B-12 or G3-9 (LIN) - Body ground*1
3B-12 or H3-9 (LIN) - Body ground*2 |
Always | 10 kΩ or higher |
*1: for RHD
*2: for LHD
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G3-1 (GND) - Body ground*1
H3-1 (GND) - Body ground*2 |
Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G3-2 (B) - Body ground*1
H3-2 (B) - Body ground*2 |
Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Power Window Regulator Motor Assembly RH (for Driver Side)) |
| *a | Front view of wire harness connector
(to Power Window Regulator Motor Assembly LH (for Driver Side)) |
*1: for RHD
*2: for LHD
A
B
Replace the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).
*1: for RHD
*2: for LHD
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B