This DTC is stored when LIN communication between the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2321 | No communication between the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 and main body ECU (multiplex network Body ECU) for 10 seconds or more. | ·
Power window regulator motor assembly RH (for driver side)*1 ·
Power window regulator motor assembly LH (for driver side)*2 ·
Main body ECU (multiplex network Body ECU) ·
Instrument panel junction block assembly ·
Harness or connector |
*1 : for RHD
*2 : for LHD
When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Inspect the fuses and for circuits related to this system before performing the following inspection procedure.
When communication between the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 and main body ECU (multiplex network Body ECU) stops, DTC B2325 is also stored.
*1 : for RHD
*2 : for LHD
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2321 is output | A |
| DTC B2321 and B2325 is output | B |
When both B2321 and B2325 are output at the same time, troubleshoot B2325 first.
A
B
Remove the main body ECU (multiplex network Body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-16 (LIN2) - 3B-12 | Always | Below 1 Ω |
| MB-16 (LIN2) or 3B-12 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG
Disconnect the G3 power window regulator motor assembly RH (for driver side)*1 or H3 power window regulator motor assembly LH (for driver side)*2 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-12 - G3-9 (LIN2)*1
3B-12 - H3-9 (LIN2)*2 |
Always | Below 1 Ω |
| 3B-12 or G3-9 (LIN2) - Body ground*1
3B-12 or H3-9 (LIN2) - Body ground*2 |
Always | 10 kΩ or higher |
*1 : for RHD
*2 : for LHD
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G3-1 (GND) - Body ground*1
H3-1 (GND) - Body ground*2 |
Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G3-2 (B) - Body ground*1
H3-2 (B) - Body ground*2 |
Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Power Window Regulator Motor Assembly RH (for Driver Side))*1 |
| *b | Front view of wire harness connector
(to Power Window Regulator Motor Assembly LH (for Driver Side))*2 |
*1 : for RHD
*2 : for LHD
OK
NG
Replace the power window regulator motor assembly RH (for driver side)*1 or power window regulator motor assembly LH (for driver side)*2 (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).
*1 : for RHD
*2 : for LHD
NEXT
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B2321 is not output | A |
| DTC B2321 is output | B |
A
B