Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248295 FRONT DOOR LOCK A

DOOR LOCK  FRONT DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 69750C 1.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.

Install the front door inside locking cable to the front door lock.


Hide 69710B 2.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.

Install the front door lock remote control cable to the front door lock.


b.
E221638

Engage the 7 claws.


Hide 69030A 3.INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)

NOTICE:
·

If reusing the front door lock assembly that has been removed, replace the door lock wire harness seal with a new seal.

·

Make sure that no grease or dirt adheres to the door lock wire harness seal surface.

·

Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock.


b.

Install the door lock wire harness seal to the front door lock.


c.
E221615E01
0.226,0.768 0.383,0.919 0.158,0.151 10 *1 0.432,0.861 1.246,0.7 false

Insert the front door lock open rod to the front door lock.

Text in Illustration
*1 Front Door Lock Open Rod
V100135

Slide Direction

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock assembly.



d.

Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


Hide 69030A 4.INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)

NOTICE:
·

If reusing the front door lock assembly that has been removed, replace the door lock wire harness seal with a new seal.

·

Make sure that no grease or dirt adheres to the door lock wire harness seal surface.

·

Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock.


b.

Install the door lock wire harness seal to the front door lock.


c.
E221615E01
0.226,0.768 0.383,0.919 0.158,0.151 10 *1 0.432,0.861 1.246,0.7 false

Insert the front door lock open rod to the front door lock.

Text in Illustration
*1 Front Door Lock Open Rod
V100135

Slide Direction

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock assembly.



d.

Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 69217E 5.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.

Temporarily install the front door lock cylinder assembly.

NOTICE:

Check the engaging the front door lock cylinder assembly to the front door lock.



b.

Using a "TORX" socket wrench T30, install the front door lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 67403F 6.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Hide 68141C 7.INSTALL FRONT DOOR GLASS RUN

Hide 68101 8.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67831 9.INSTALL FRONT DOOR SERVICE HOLE COVER (for 5 Door)

Hide 67831 10.INSTALL FRONT DOOR SERVICE HOLE COVER (for 3 Door)

Hide 67601 11.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)

Hide 67601 12.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)

Hide 74231 13.INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74231 14.INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 69260 15.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)