Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051502 DOOR / HATCH _0248392 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


PROCEDURE

Hide 1.APPLY BODY GREASE

Hide 75921C 2.INSTALL NO. 1 BLACK OUT TAPE (for 5 Door)

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>INSTALLATION)


Hide 67001A 3.INSTALL FRONT DOOR PANEL CUSHION

a.
B271614

Install the 2 cushions onto the door panel.


Hide 67861 4.INSTALL FRONT DOOR WEATHERSTRIP (for 5 Door)

a.
B271613

Engage the 29 clips and install the front door weatherstrip.


b.

Engage the clip.


Hide 67861 5.INSTALL FRONT DOOR WEATHERSTRIP (for 3 Door)

a.
B284595

Engage the 32 clips and install the front door weatherstrip.


b.

Engage the clip.


Hide 68610B 6.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check.


b.
B271610

Install the front door check onto the door panel with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the front door check onto the body panel with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69311A 7.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B268986E01
1.203,2.311 1.303,2.457 0.099,0.145 10 1 0.548,2.098 0.647,2.244 0.099,0.145 10 2 0.464,1.516 0.623,1.661 0.158,0.145 10 *1 0.945,2.213 0.639,1.593 false

Install the front door lock open rod as indicated by the arrows in the order shown in the illustration.

Text in Illustration
*1 Snap


Hide 69201A 8.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door outside handle frame.


b.
B271622E01
2.63,0.1 2.791,0.263 0.162,0.162 10 *1 2.601,0.192 2.191,0.695 false

Slide the front door outside handle frame to install it.

Text in Illustration
*1 Grommet


c.

Engage the grommet and 2 claws.


d.
B271625

Using a "TORX" socket wrench T30, install the front door outside handle frame with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242E 9.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B271620

Engage the 2 claws and install the front door outside handle rear pad.


Hide 69241H 10.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B271619

Engage the 3 claws and install the front door outside handle front pad.


Hide 69210 11.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B271618

Pushing the front door outside handle in the direction of the arrow mark shown in the illustration, install the front door outside handle.


Hide 69030A 12.INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)

Hide 69030A 13.INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)

Hide 69217E 14.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.
B271703

Engage the 2 guides.


b.

Engage the claw and install the front door outside handle cover.


c.
B271615

Temporarily install the front door outside handle cover.


d.

Using a "TORX" socket wrench T30, install the front door outside handle cover.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


e.

Install the hole plug.


Hide 68215 15.INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP

a.

Install the front door fix window glass onto the front door fix window weatherstrip.


b.
B271612

Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to install it.


Hide 67401F 16.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B271609

Install the front door front lower frame with the 2 bolts and screw.

Torque:
Bolt : 6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 67403F 17.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B271608

Engage the guide.


b.

Install the front door rear lower frame with the bolt.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68141C 18.INSTALL FRONT DOOR GLASS RUN

a.
B271607

Install the front door glass run.


Hide 69801 19.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)

a.

Apply MP grease to the sliding parts of the front door window regulator.


b.

Install the temporary bolt.


c.
B271605E06
1.438,0.802 1.604,0.146 false 1.646,0.063 1.792,0.219 0.146,0.156 10 true *1 1.156,0.135 1.281,0.313 0.125,0.177 10 true 2 1.771,0.365 1.906,0.573 0.135,0.208 10 true 4 0.708,1.5 0.844,1.656 0.135,0.156 10 true 3 1.125,1.583 1.26,1.781 0.135,0.198 10 true 1

Insert the front door window regulator into the door panel. Use the temporary bolt to hang the front door window regulator on the door panel.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the 3 bolts and the temporary bolt in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the front door window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.

Connect the connector.


Hide 69801 20.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)

a.

Apply MP grease to the sliding parts of the front door window regulator.


b.

Install the temporary bolt.


c.
B284589E04
1.104,1.49 1.333,1.083 false 1.021,1.49 1.198,1.688 0.177,0.198 10 true *1 0.896,0.354 1.021,0.552 0.125,0.198 10 true 1 1.406,1.375 1.552,1.552 0.146,0.177 10 true 2 0.604,1.323 0.74,1.521 0.135,0.198 10 true 3

Insert the front door window regulator into the door panel. Use the temporary bolt to hang the front door window regulator on the door panel.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the 2 bolts and temporary bolt in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the front door window regulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68101 21.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the power window regulator master switch and move the front door glass so that the door glass bolt holes can be seen.


c.

Disconnect the cable from the negative (-) battery terminal and the power window regulator master switch.


d.
B271604E03
0.969,0.521 1.094,0.698 0.125,0.177 10 true 1 1.802,0.052 1.927,0.229 0.125,0.177 10 true 2

Insert the front door glass into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass.



e.
B271602

Install the front door glass with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.
B271601

Install the front door service hole cover.


Hide 67831 22.INSTALL FRONT DOOR SERVICE HOLE COVER (for 5 Door)

a.

Apply butyl tape to the front door panel.


b.

Pass the front door lock remote control cable, front door inside locking cable and each connector through a new front door service hole cover.


c.
B271702E01
0.119,0.293 0.269,0.446 0.150,0.153 10 *a 0.291,0.392 0.412,0.524 false 3.166,0.261 3.316,0.414 0.150,0.153 10 *a 3.02,3.11 3.170,3.263 0.150,0.153 10 *a 2.883,3.096 3.012,3.208 false 2.998,0.46 3.161,0.362 false

Install a new front door service hole cover according to the reference points on the front door panel.

Text in Illustration
*a Reference Point

HINT:

Securely install the front door service hole cover taking care to prevent wrinkles.



Hide 67831 23.INSTALL FRONT DOOR SERVICE HOLE COVER (for 3 Door)

a.

Apply butyl tape to the front door panel.


b.

Pass the front door lock remote control cable, front door inside locking cable and each connector through a new front door service hole cover.


c.
B284588E01
0.13,0.713 0.282,0.865 0.152,0.152 10 *a 3.091,0.451 3.242,0.603 0.152,0.152 10 *a 2.522,3.032 2.673,3.184 0.152,0.152 10 *a 0.312,0.814 0.442,0.884 false 3.091,0.552 2.961,0.653 false 2.697,3.134 2.838,3.097 false

Install a new front door service hole cover according to the reference points on the front door panel.

Text in Illustration
*a Reference Point

HINT:

Securely install the front door service hole cover taking care to prevent wrinkles.



Hide 89865 25.INSTALL DOOR SIDE AIRBAG SENSOR (for 3 Door)

a.

w/ Curtain Shield Airbag:



Hide 68160C 26.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>INSTALLATION).


Hide 75755C 27.INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

Hide 87910 28.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

HINT:

Use the same procedure as for the LH side (See page Vehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSTALLATION).


Hide 75754A 29.INSTALL FRONT DOOR WINDOW FRAME UPPER MOULDING (for Driver Side)

Hide 75751C 30.INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

Hide 68171B 31.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP (for 5 Door)

a.
B271701

Engage the 7 claws and install the front door glass inner weatherstrip as shown in the illustration.


Hide 68171B 32.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP (for 3 Door)

a.
B284626

Engage the 8 claws and install the front door glass inner weatherstrip as shown in the illustration.


Hide 69205 33.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B271598

Engage the 4 guides and install the front door inside handle.


Hide 67601 34.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)

a.
B271597E01
2.813,0.686 2.977,0.850 0.164,0.164 10 *1 2.799,1.71 2.963,1.874 0.164,0.164 10 *2 2.776,0.793 2.544,1.117 false 2.773,1.802 2.547,1.478 false

Connect the front door lock remote control cable and the front door inside locking cable to the front door inside handle.

Text in Illustration
*1 Front Door Lock Remote Control Cable Assembly
*2 Front Door Inside Locking Cable Assembly


b.
B271596

Engage the 7 clips and the front door trim board.


c.
B271595

Install the 3 screws.


d.
B275407

Engage the claw and close the cover.


Hide 67601 35.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)

a.
B271597E01
2.813,0.686 2.977,0.850 0.164,0.164 10 *1 2.799,1.71 2.963,1.874 0.164,0.164 10 *2 2.776,0.793 2.544,1.117 false 2.773,1.802 2.547,1.478 false

Connect the front door lock remote control cable and the front door inside locking cable to the front door inside handle.

Text in Illustration
*1 Front Door Lock Remote Control Cable Assembly
*2 Front Door Inside Locking Cable Assembly


b.
B284585

Engage the 8 clips and the front door trim board.


c.
B271595

Install the 3 screws.


d.
B275407

Engage the claw and close the cover.


Hide 74231 36.INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

a.

Connect the connector.


b.
B284582

Engage the 9 claws and 4 guides, and install the front armrest base upper panel.


Hide 74231 37.INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

a.

Connect the connector.

HINT:

If the armrest base upper panel is equipped with door lock switch, connect the connector.



b.
B284583

Engage the 6 claws and 3 guides, and install the front armrest base upper panel.


Hide 69260 38.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B271669E01
2.418,0.657 2.574,0.813 0.156,0.156 10 *a

Install the window regulator handle plate.

Text in Illustration
*a Inside of Vehicle


b.

Open all the windows.


c.
B284599E01
2.652,0.731 2.965,0.877 0.313,0.145 10 36° 2.175,0.271 2.488,0.416 0.313,0.145 10 60° 2.458,0.271 2.614,0.416 0.156,0.145 10 *a

Install the front door window regulator handle with clip at the angle shown in the illustration.

Text in Illustration
*a Assemble with Glass in Fully Open Position


Hide 39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)