Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248296 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


PROCEDURE

Hide 1.APPLY BODY GREASE

Hide 69770B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.

Install the rear door inside locking cable to rear door lock.


b.
E221632

Engage the 4 claws.


Hide 69730D 3.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.

Install the rear door lock remote control cable to the rear door lock.


b.
E221631

Engage the 2 claws.


Hide 69050A 4.INSTALL REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock)

NOTICE:
·

If reusing the rear door lock assembly that has been removed, replace the connector seal with a new door lock wire harness seal.

·

Make sure that no grease or dirt adheres to the door lock wire harness seal surface.

·

Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the rear door lock.



a.

Install a new door lock wire harness seal to the rear door lock.


b.

Apply MP grease to the sliding parts of the rear door lock.


c.
E221619E01
0.191,1.1 0.344,1.245 0.153,0.145 10 *1 0.387,1.186 1.27,0.848 false

Insert the rear door lock to the release plate.

Text in Illustration
*1 Release Plate
V100135

Slide Direction

HINT:

Make sure that the release plate is securely connected to the rear door lock.



d.

Using a "TORX" socket wrench T30, install the rear door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


Hide 69050A 5.INSTALL REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock)

NOTICE:
·

If reusing the rear door lock assembly that has been removed, replace the connector seal with a new door lock wire harness seal.

·

Make sure that no grease or dirt adheres to the door lock wire harness seal surface.

·

Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the rear door lock.



a.

Install a new door lock wire harness seal to the rear door lock.


b.

Apply MP grease to the sliding parts of the rear door lock.


c.
E221619E01
0.191,1.1 0.344,1.245 0.153,0.145 10 *1 0.387,1.186 1.27,0.848 false

Insert the rear door lock to the release plate.

Text in Illustration
*1 Release Plate
V100135

Slide Direction

HINT:

Make sure that the release plate is securely connected to the rear door lock.



d.

Using a "TORX" socket wrench T30, install the rear door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 68142C 6.INSTALL REAR DOOR GLASS RUN

Hide 68103 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67407E 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 67841E 9.INSTALL REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

Hide 67841E 10.INSTALL REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

Hide 67603 11.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74271A 12.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74271A 13.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 69260E 14.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 67673A 15.INSTALL REAR DOOR FRAME GARNISH