Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the theft warning indicator light assembly blinks continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B271399E10
1.865,0.51 2.677,0.667 0.813,0.156 10 false from Battery 5.667,1.021 5.854,1.177 0.188,0.156 10 false 2 5.854,1.156 6.333,1.313 0.479,0.156 10 false IG 5.667,1.76 5.854,1.917 0.188,0.156 10 false 8 5.51,2.844 5.771,3 0.26,0.156 10 false F54 5.854,2.458 6.333,2.615 0.479,0.156 10 false GND 5.594,2.354 5.781,2.51 0.188,0.156 10 false 16 5.833,0.521 6.313,0.677 0.479,0.156 10 false +B 5.667,0.417 5.781,0.573 0.115,0.156 10 false 1 4.219,1.292 4.469,1.448 0.25,0.156 10 false IG2 1.698,1.135 2.698,1.292 1,0.156 10 false from IG2 Relay 1.292,1.781 1.396,1.938 0.104,0.156 10 false 6 2.698,1.781 2.938,1.938 0.24,0.156 10 false 2 1.479,1.875 1.708,2.031 0.229,0.156 10 false E 2.417,1.896 2.646,2.052 0.229,0.156 10 false LP 5.844,1.854 6.167,2.01 0.323,0.156 10 false IND 1.281,2.448 2.771,2.76 1.49,0.313 10 false Theft Warning Indicator Light Assembly 1.281,2.271 1.583,2.427 0.302,0.156 10 false F56 4.469,0.677 5.375,0.833 0.906,0.156 10 false ECU-B NO. 1 3.667,0.667 4.063,0.823 0.396,0.156 10 false D.C.C 5.5,3 6.917,3.417 1.417,0.417 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.



PROCEDURE

1.CHECK FOR DTC

OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Theft warning indicator light assembly OFF / ON -

OK:

Theft warning indicator light assembly can be turned on and off using the intelligent tester.




OK

3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT WARNING INDICATOR LIGHT ASSEMBLY)
3.READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)
a.

Turn the ignition switch off.

HINT:

When using the intelligent tester with the ignition switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 second until communication between the intelligent tester and vehicle begins.



b.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST).

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - THEFT WARNING INDICATOR LIGHT ASSEMBLY)
a.

Disconnect the F54 transponder key ECU assembly connector.


b.

Disconnect the F56 theft warning indicator light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-8 (IND) - F56-2 (LP) Always Below 1 Ω
F56-6 (E) - Body ground Always Below 1 Ω
F54-8 (IND) - Body ground Always 10 kΩ or higher




OK

5.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT THEFT WARNING INDICATOR LIGHT ASSEMBLY
a.

Inspect the theft warning indicator light assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>INSPECTION).



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U158148E02
2.521,1.396 2.604,1.781 false 1.021,1.208 0.865,1.802 false 0.865,1.188 0.427,1.479 false 0.115,0.104 0.313,0.281 0.198,0.177 10 false *a 0.219,1.427 0.448,1.625 0.229,0.198 10 false +B 2.521,1.813 2.854,2.01 0.333,0.198 10 false GND 0.802,1.823 1.031,2.021 0.229,0.198 10 false IG 1.625,0.375 2,0.573 0.375,0.198 10 false F54

Disconnect the F54 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-16 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F54-1 (+B) - Body ground Always 11 to 14 V
F54-2 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR