Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

The key ID code of the transponder chip inside the IG key is compared against the key ID code registered in the transponder key ECU assembly. While checking the code, the transponder key ECU assembly supplies electrical power to the transponder chip in the key by means of the transponder key amplifier. If the codes match, the immobilizer is then UNSET (released), and after the E/G start permission signal is sent to the ECM, if communication is functioning properly, E/G start can be performed.

WIRING DIAGRAM

B255097E06
0.713,1.956 1.006,2.131 0.293,0.174 10 A74 0.713,2.127 1.065,2.287 0.352,0.160 10 ECM 5.734,0.482 6.128,0.670 0.394,0.188 10 EFIO 5.734,1.23 6.128,1.418 0.394,0.188 10 EFII 1.276,0.466 1.516,0.653 0.240,0.188 10 IMI 1.22,1.23 1.515,1.418 0.295,0.188 10 IMO 5.406,0.363 5.629,0.573 0.224,0.210 10 13 5.425,1.124 5.649,1.334 0.224,0.210 10 12 5.314,1.933 5.724,2.119 0.410,0.186 10 F54 5.314,2.107 6.751,2.421 1.437,0.314 10 Transponder Key ECU Assembly 1.57,0.377 1.748,0.558 0.178,0.181 10 11 1.57,1.139 1.748,1.320 0.178,0.181 10 10

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.

·

When replacing the ECM, refer to the INITIALIZATION (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Result
Result Proceed to
No DTC output A
DTC output B



A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser fuel cut/
OFF or ON
- -

OK:

The item in the Data List indicates "OFF"


Result
Result Proceed to
NG A
OK (for 2NZ-FE) B
OK (for 1NZ-FE) C



A

3.CHECK WHETHER ENGINE STARTS

B

C

3.CHECK WHETHER ENGINE STARTS
a.

It leaves for 5 seconds by the ignition switch ON status, and the engine starting operation is done.

Result
Result Proceed to
Engine cannot be started A
Engine can be started B



A

4.CHECK ECM (TERMINAL IMI)

B

4.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U158203E02
3.521,2.938 3.198,3.25 true 4.948,0.719 5.51,2.177 false 2.115,2.719 2.375,2.896 0.26,0.177 10 false F54 5.604,0.125 5.865,0.302 0.26,0.177 10 false A74 5.458,2.198 5.813,2.375 0.354,0.177 10 false IMI 0.198,0.125 0.365,0.281 0.167,0.156 10 false *a 0.646,3.375 0.813,3.531 0.167,0.156 10 false *c 0.646,5.25 0.813,5.406 0.167,0.156 10 false *d 3,3.271 3.354,3.448 0.354,0.177 10 false EFIO 0.563,4.573 0.927,4.75 0.365,0.177 10 false GND 0.563,6.365 0.927,6.542 0.365,0.177 10 false GND 1.625,4.688 1.792,4.844 0.167,0.156 10 false *e 1.427,6.479 1.594,6.635 0.167,0.156 10 false *e 2.208,2.219 2.375,2.375 0.167,0.156 10 false *b

Text in Illustration
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform A - -

Measurement Condition
Item Content
Tester Connection A74-11 (IMI) - F54-13 (EFIO)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform A) not output, or has abnormal wavelength or shape B


A

5.CHECK ECM (TERMINAL IMO)

B

9.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
5.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

U158205E02
3.594,2.938 3.344,3.25 false 5.083,0.729 5.656,2.188 false 2.115,2.719 2.375,2.896 0.26,0.177 10 false F54 5.583,0.135 5.844,0.313 0.26,0.177 10 false A74 5.604,2.219 5.958,2.396 0.354,0.177 10 false IMO 0.177,0.135 0.344,0.292 0.167,0.156 10 false *a 0.625,3.354 0.792,3.51 0.167,0.156 10 false *c 0.625,5.24 0.792,5.396 0.167,0.156 10 false *d 3.208,3.26 3.563,3.438 0.354,0.177 10 false EFII 0.552,4.583 0.917,4.76 0.365,0.177 10 false GND 0.552,6.375 0.917,6.552 0.365,0.177 10 false GND 1.604,3.729 1.771,3.885 0.167,0.156 10 false *e 1.385,5.531 1.552,5.688 0.167,0.156 10 false *e 2.198,2.219 2.365,2.375 0.167,0.156 10 false *b 1.75,4.688 1.917,4.844 0.167,0.156 10 false *g 1.552,6.49 1.719,6.646 0.167,0.156 10 false *h 1.167,6.49 1.333,6.646 0.167,0.156 10 false *f 1.156,4.698 1.323,4.854 0.167,0.156 10 false *f

Text in Illustration
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform B *f 160 ms
*g 510 ms *h 270 ms

Measurement Condition
Item Content
Tester Connection A74-10 (IMO) - F54-12 (EFII)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 2NZ-FE) B
Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 1NZ-FE) C


A

6.CHECK ECM (TERMINAL IMI)

B

C

6.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U158207E02
3.521,2.938 3.198,3.26 true 4.938,0.719 5.5,2.177 false 2.104,2.688 2.365,2.865 0.26,0.177 10 false F54 5.583,0.125 5.844,0.302 0.26,0.177 10 false A74 5.448,2.208 5.802,2.385 0.354,0.177 10 false IMI 0.177,0.125 0.344,0.281 0.167,0.156 10 false *a 0.615,3.396 0.781,3.552 0.167,0.156 10 false *c 0.615,5.26 0.781,5.417 0.167,0.156 10 false *d 3.063,3.271 3.417,3.448 0.354,0.177 10 false EFIO 0.573,4.583 0.938,4.76 0.365,0.177 10 false GND 0.563,6.365 0.927,6.542 0.365,0.177 10 false GND 2.844,3.708 3.01,3.865 0.167,0.156 10 false *e 2.979,4.677 3.146,4.833 0.167,0.156 10 false *g 2.375,4.688 2.542,4.844 0.167,0.156 10 false *f 2.375,6.479 2.542,6.635 0.167,0.156 10 false *h 2,6.479 2.167,6.635 0.167,0.156 10 false *f 2.229,5.49 2.396,5.646 0.167,0.156 10 false *e 2.188,2.198 2.354,2.354 0.167,0.156 10 false *b

Text in Illustration
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform C *f 160 ms
*g 510 ms *h 270 ms

Measurement Condition
Item Content
Tester Connection A74-11 (IMI) - F54-13 (EFIO)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform C) not output, or has abnormal wavelength or shape B



A

7.REGISTER ECU COMMUNICATION ID

B

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
7.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID (Refer to Service Bulletin).



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with the key.

OK:

Engine starts normally.




OK

END

NG

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the A74 ECM connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-11 (IMI) - F54-13 (EFIO) Always Below 1 Ω
F54-13 (EFIO) - Body ground Always 10 kΩ or higher




OK

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).


b.

Check that the engine starts with the key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 2NZ-FE) B
NG (for 1NZ-FE) C



A

END

B

C