Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2014.07–2015.06
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the engine immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B255097E38
0.792,1.99 2.365,2.26 1.573,0.271 10 false A74 0.792,2.146 1.385,2.448 0.594,0.302 10 false ECM 5.396,1.885 5.844,2.302 0.448,0.417 10 false F54 5.396,2.042 6.802,2.5 1.406,0.458 10 false Transponder Key ECU Assembly 1.219,1.271 1.656,1.583 0.438,0.313 10 false IMO 1.24,0.521 1.677,0.833 0.438,0.313 10 false IMI 5.719,1.24 6.292,1.625 0.573,0.385 10 false EFII 5.719,0.479 6.458,0.771 0.74,0.292 10 false EFIO 5.469,1.135 5.802,1.396 0.333,0.26 10 false 12 5.469,0.375 6.073,0.823 0.604,0.448 10 false 13 1.604,1.135 2.771,1.49 1.167,0.354 10 false 10 1.604,0.365 2.906,0.802 1.302,0.438 10 false 11

CAUTION / NOTICE / HINT

NOTICE:

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


Result
Result Proceed to
No DTC output A
DTC output B



A

2.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)

B

2.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Stored as Freeze Frame Data
Immobiliser Fuel Cut Status of immobiliser fuel cut/
ON or OFF
- Yes

OK:

The item in the Data List indicates "OFF"


Result
Result Proceed to
NG A
OK (for 1NZ-FE) B
OK (for 2NZ-FE) C



A

3.CHECK WHETHER ENGINE STARTS

B

C

3.CHECK WHETHER ENGINE STARTS
a.

It leaves for 5 seconds by the ignition switch ON status, and the engine starting operation is done.

Result
Result Proceed to
Engine cannot be started A
Engine can be started B



A

4.CHECK ECM (TERMINAL IMI)

B

4.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U158203E02
3.521,2.938 3.198,3.25 true 4.948,0.719 5.51,2.177 false 2.115,2.719 2.375,2.896 0.26,0.177 10 false F54 5.604,0.125 5.865,0.302 0.26,0.177 10 false A74 5.458,2.198 5.813,2.375 0.354,0.177 10 false IMI 0.198,0.125 0.365,0.281 0.167,0.156 10 false *a 0.646,3.375 0.813,3.531 0.167,0.156 10 false *c 0.646,5.25 0.813,5.406 0.167,0.156 10 false *d 3,3.271 3.354,3.448 0.354,0.177 10 false EFIO 0.563,4.573 0.927,4.75 0.365,0.177 10 false GND 0.563,6.365 0.927,6.542 0.365,0.177 10 false GND 1.625,4.688 1.792,4.844 0.167,0.156 10 false *e 1.427,6.479 1.594,6.635 0.167,0.156 10 false *e 2.208,2.219 2.375,2.375 0.167,0.156 10 false *b

Text in Illustration
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform A - -

Measurement Condition
Item Content
Tester Connection F74-11 (IMI) - F54-13 (EFIO)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform A) not output, or has abnormal wavelength or shape B


A

5.CHECK ECM (TERMINAL IMO)

B

9.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
5.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

i.

Using an oscilloscope, check the waveform.

U158205E02
3.594,2.938 3.344,3.25 false 5.083,0.729 5.656,2.188 false 2.115,2.719 2.375,2.896 0.26,0.177 10 false F54 5.583,0.135 5.844,0.313 0.26,0.177 10 false A74 5.604,2.219 5.958,2.396 0.354,0.177 10 false IMO 0.177,0.135 0.344,0.292 0.167,0.156 10 false *a 0.625,3.354 0.792,3.51 0.167,0.156 10 false *c 0.625,5.24 0.792,5.396 0.167,0.156 10 false *d 3.208,3.26 3.563,3.438 0.354,0.177 10 false EFII 0.552,4.583 0.917,4.76 0.365,0.177 10 false GND 0.552,6.375 0.917,6.552 0.365,0.177 10 false GND 1.604,3.729 1.771,3.885 0.167,0.156 10 false *e 1.385,5.531 1.552,5.688 0.167,0.156 10 false *e 2.198,2.219 2.365,2.375 0.167,0.156 10 false *b 1.75,4.688 1.917,4.844 0.167,0.156 10 false *g 1.552,6.49 1.719,6.646 0.167,0.156 10 false *h 1.167,6.49 1.333,6.646 0.167,0.156 10 false *f 1.156,4.698 1.323,4.854 0.167,0.156 10 false *f

Text in Illustration
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform B *f 160 ms
*g 510 ms *h 270 ms

Measurement Condition
Item Content
Tester Connection F74-10 (IMO) - F54-12 (EFII)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected



OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 1NZ-FE) B
Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 2NZ-FE) C


A

6.CHECK ECM (TERMINAL IMI)

B

C

6.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U158208E01
2.102,2.689 2.358,2.871 0.256,0.181 10 F54 5.594,0.111 5.858,0.293 0.264,0.181 10 A74 5.41,2.202 5.768,2.382 0.357,0.180 10 IMI 0.169,0.113 0.339,0.274 0.170,0.161 10 *a 0.613,3.334 0.783,3.495 0.170,0.161 10 *c 0.613,5.221 0.783,5.382 0.170,0.161 10 *d 3.066,3.272 3.424,3.453 0.357,0.180 10 EFIO 3.537,2.927 3.219,3.247 false 4.933,0.714 5.504,2.174 false 0.549,4.561 0.909,4.741 0.360,0.180 10 GND 0.549,6.36 0.909,6.540 0.360,0.180 10 GND 2.839,3.682 3.009,3.842 0.170,0.161 10 *e 2.979,4.687 3.149,4.847 0.170,0.161 10 *g 2.377,4.687 2.547,4.847 0.170,0.161 10 *f 2.377,6.48 2.547,6.641 0.170,0.161 10 *h 1.999,6.48 2.168,6.641 0.170,0.161 10 *f 2.237,5.485 2.406,5.646 0.170,0.161 10 *e 2.191,2.199 2.360,2.360 0.170,0.161 10 *b

Text in Illustration
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform 1 *d Waveform 2
*e Waveform C *f 160 ms
*g 510 ms *h 270 ms

Measurement Condition
Item Content
Tester Connection F74-11 (IMI) - F54-13 (EFIO)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected


OK:

Waveform is output normally (refer to illustration).


Result
Result Proceed to
Normal waveform A
Waveform 1 or 2 (Waveform C) not output, or has abnormal wavelength or shape B


A

7.REGISTER ECU COMMUNICATION ID

B

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (Refer to Service Bulletin).



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with the key.

OK:

Engine starts normally.




OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the F74 ECM connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-11 (IMI) - F54-13 (EFIO) Always Below 1 Ω
F73-11 (IMI) or F54-13 (EFIO) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).


b.

Check that the engine starts with the key.

OK:

Engine starts normally.


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

END

B

C