Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051491 THEFT DETERRENT / KEYLESS ENTRY _0248300 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Key Cannot be Registered  


DESCRIPTION

A maximum of 5 master key codes and 3 sub key codes can be registered.

CAUTION / NOTICE / HINT

NOTICE:

When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.


PROCEDURE

1.CHECK REGISTRATION MODE
a.

Check that the system enters registration mode.

OK:

System enters registration mode




OK

2.CHECK THEFT WARNING INDICATOR LIGHT OPERATION

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
2.CHECK THEFT WARNING INDICATOR LIGHT OPERATION
a.

In the registration mode, when the key inserted in ignition key cylinder, check that the theft warning indicator light assembly.

HINT:

If the new key code registration fails, code 2-1 will be output through the theft warning indicator light assembly. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the theft warning indicator light assembly. The output details are shown below.


B111593E55
2.469,8.094 2.396,8.417 false 2.958,8.094 3.063,8.417 false 2.469,6 2.396,6.323 false 2.958,6 3.063,6.323 false 2.469,3.906 2.396,4.219 false 2.958,3.906 3.063,4.219 false 0.229,1.542 1.5,2.021 1.271,0.479 10 false Normal (Immobiliser system is operating normally) 0.229,3.51 0.823,3.656 0.594,0.146 10 false Code 2-1 0.229,5.646 0.875,5.833 0.646,0.188 10 false Code 2-2 0.229,7.688 0.896,7.875 0.667,0.188 10 false Code 2-3 2.021,0.688 2.958,0.896 0.938,0.208 10 false 0.12 seconds 2.76,2.063 3.729,2.271 0.969,0.208 10 false 1.88 seconds 1.688,1.281 1.948,1.438 0.26,0.156 10 false On 1.656,1.719 1.979,1.865 0.323,0.146 10 false Off 1.719,3.188 1.969,3.333 0.25,0.146 10 false On 1.698,3.625 2.021,3.771 0.323,0.146 10 false Off 1.74,5.271 2.021,5.406 0.281,0.135 10 false On 1.708,5.708 2.042,5.854 0.333,0.146 10 false Off 2.01,2.542 2.958,2.708 0.948,0.167 10 false 0.25 seconds 1.844,8.469 2.708,8.604 0.865,0.135 10 false 0.25 seconds 2.854,8.458 3.844,8.594 0.99,0.135 10 false 0.5 seconds 2.052,6.813 2.917,6.99 0.865,0.177 10 false 0.25 seconds 1.844,6.365 2.708,6.5 0.865,0.135 10 false 0.25 seconds 2.854,6.354 3.844,6.49 0.99,0.135 10 false 0.5 seconds 1.844,4.26 2.708,4.458 0.865,0.198 10 false 0.25 seconds 2.854,4.25 3.844,4.458 0.99,0.208 10 false 0.5 seconds 3.375,2.688 4.26,2.833 0.885,0.146 10 false 1 second 1.75,7.375 1.99,7.521 0.24,0.146 10 false On 1.74,7.813 2.063,7.958 0.323,0.146 10 false Off 2.052,4.677 3.042,4.865 0.99,0.188 10 false 0.25 seconds 0.146,0.083 2,0.292 1.854,0.208 10 false Theft Warning Indicator Light: 3.75,4.802 4.635,4.948 0.885,0.146 10 false 1 second 4.094,6.896 4.979,7.042 0.885,0.146 10 false 1 second

Result
Result Proceed to
Code 2-1 A
Code 2-2 B
Code 2-3 C



A

3.READ VALUE USING INTELLIGENT TESTER

B

REGISTRATION AS ANOTHER KEY

C

3.READ VALUE USING INTELLIGENT TESTER
3.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Transponder S-code Number of registered sub-keys / min.: 0, max.: 15 Number of registered sub-keys -
Transponder M-code Number of registered master keys / min.: 0, max.: 15 Number of registered master keys -

Result
Result Proceed to
None of the below A
Registered master keys: 5, registered sub-keys: 0 B
Registered master keys: 0, registered sub-keys: 3 C
Registered master keys: 5, registered sub-keys: 3 D



A

4.KEY REGISTRATION

B

KEY REGISTRATION (SUB-KEY)

C

KEY REGISTRATION (MASTER KEY)

D

NOT KEY REGISTRATION

4.KEY REGISTRATION
a.

Refer to the table below to determine if additional keys can be registered.

Number of Keys Registered (Master and Sub) Proceed to
0 New key ID registration (refer to the Service Bulletin)
1 to 7 Additional key ID registration (refer to the Service Bulletin)


b.

Check whether key registration.



OK

END (KEY MALFUNCTION)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH)
a.

Disconnect the F15 unlock warning switch assembly connector.


b.

Disconnect the F54 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-1 - F54-3 (KSW) Always Below 1 Ω
F15-2 - Body ground Always Below 1 Ω
F15-1 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (not using intelligent tester) A
OK (using intelligent tester) B
NG C



A

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Inspect the front door courtesy light switch assembly LH (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION).



OK

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH)
a.

Disconnect the F54 transponder key ECU assembly connector.


b.

Disconnect the K1 front door courtesy light switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F54-7 (CTY) - K1-1 Always Below 1 Ω
F54-7 (CTY) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR