Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2014.07
RM19S0E _58 Vehicle Interior _051492 LIGHTING (INT) _0248303 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU controls the map light assembly.

WIRING DIAGRAM

E295321E03
1.302,0.813 2.208,1.083 0.906,0.271 10 false from Battery 2.667,0.969 3.25,1.25 0.583,0.281 10 false DOME 3.375,0.823 3.667,1.021 0.292,0.198 10 false 3C 3.417,0.646 3.604,0.844 0.188,0.198 10 false 4 3.365,1.667 3.656,1.865 0.292,0.198 10 false 3A 3.417,1.458 3.604,1.656 0.188,0.198 10 false 5 3.375,2.24 3.667,2.438 0.292,0.198 10 false 3B 3.406,2.042 3.594,2.24 0.188,0.198 10 false 6 5.625,2.24 5.917,2.438 0.292,0.198 10 false MB 5.667,2.042 5.854,2.24 0.188,0.198 10 false 1 5.948,2.24 6.24,2.438 0.292,0.198 10 false ILE 2.302,2.115 2.698,2.281 0.396,0.167 10 false GND 2.479,2.917 2.698,3.115 0.219,0.198 10 false E 0.792,2.396 0.979,2.573 0.188,0.177 10 false B 0.625,2.396 0.813,2.594 0.188,0.198 10 false 3 2.708,2.104 2.896,2.302 0.188,0.198 10 false 2 2.677,2.917 2.865,3.115 0.188,0.198 10 false 1 2.156,4.813 2.552,4.979 0.396,0.167 10 false GND 2.188,5.333 2.583,5.531 0.396,0.198 10 false CTY 0.927,5.073 1.323,5.271 0.396,0.198 10 false +B1 0.823,5.823 1.219,6.021 0.396,0.198 10 false L10 2.542,4.813 2.729,5.01 0.188,0.198 10 false 2 2.552,5.333 2.74,5.531 0.188,0.198 10 false 3 0.75,5.073 0.938,5.271 0.188,0.198 10 false 1 1.01,3.542 1.219,3.729 0.208,0.188 10 false L9 1.01,3.708 2.354,3.885 1.344,0.177 10 false Map Light Assembly 0.813,5.969 2.594,6.302 1.781,0.333 10 false No. 1 Room Light Assembly 3.625,5.531 5.729,5.969 2.104,0.438 10 false Instrument Panel Junction Block Assembly 5.813,6.188 6.885,6.438 1.073,0.25 10 false Main Body ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ILLUMINATED ENTRY SYSTEM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Turn the map light assembly switch to the DOOR position.


e.

All doors closed (door courtesy light switches OFF).


f.

Enter the following menus: Body / Main Body / Active Test.


g.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System
·

Map light assembly

·

No. 1 room light assembly


OFF or ON Map light switch and No. 1 room light assembly at DOOR position and all doors closed.

OK:

The illuminated entry system operates normally when operating it through the intelligent tester.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
U158726E02
0.125,0.094 0.292,0.25 0.167,0.156 10 false *a 1.573,0.354 1.76,0.531 0.188,0.177 10 false 3B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3B-6 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(Instrument Panel Junction Block Assembly)



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Remove the main body ECU from the instrument panel junction block assembly.

U158727E01
3.489,0.919 3.529,1.129 false 3.423,1.138 3.661,1.291 0.238,0.153 10 ILE 1.493,0.189 1.680,0.371 0.187,0.181 10 3B 4.841,0.199 5.066,0.381 0.225,0.181 10 MB 0.147,0.088 0.317,0.249 0.170,0.161 10 *a

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-6 - MB-1 (ILE) Always Below 1 Ω




OK

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY