Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051492 LIGHTING (INT) _0248303 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU.

WIRING DIAGRAM

E231469E01
5.579,0.718 5.777,0.888 0.198,0.170 10 32 5.898,0.902 6.076,1.059 0.178,0.156 10 IG 3.663,1.445 4.575,1.595 0.913,0.150 10 ECU-IG NO. 1 3.778,2.873 4.424,3.019 0.645,0.147 10 IG1 NO. 1 3.151,1.751 3.252,1.921 0.101,0.170 10 1 2.817,1.751 2.916,1.921 0.099,0.170 10 1 3.112,0.721 3.291,0.868 0.178,0.147 10 40 3.114,1.138 3.289,1.289 0.175,0.151 10 54 3.112,2.389 3.291,2.558 0.178,0.170 10 29 3.103,1.933 3.300,2.071 0.198,0.139 10 3F 3.103,0.904 3.300,1.057 0.198,0.153 10 3A 3.103,1.319 3.300,1.465 0.198,0.147 10 3A 3.103,3.57 3.300,3.740 0.198,0.170 10 3B 5.564,0.906 5.792,1.055 0.229,0.149 10 MB 3.103,2.556 3.300,2.726 0.198,0.170 10 3A 2.768,1.927 2.965,2.077 0.198,0.150 10 3E 3.103,2.13 3.300,2.300 0.198,0.170 10 *2 2.768,2.13 2.965,2.300 0.198,0.170 10 *1 3.149,3.384 3.255,3.554 0.106,0.170 10 8 3.782,4.027 5.409,4.340 1.627,0.312 10 Instrument Panel Junction Block Assembly 1.13,1.912 1.918,2.085 0.788,0.173 10 from Battery 0.683,2.558 1.914,2.724 1.231,0.166 10 from Ignition Switch 0.922,3.871 1.637,4.035 0.715,0.164 10 *1: for LHD 0.922,4.236 1.674,4.406 0.752,0.171 10 *2: for RHD 5.77,4.4 6.787,4.551 1.017,0.151 10 Main Body ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal /
OFF or ON
OFF: Ignition switch ACC or off
ON: Ignition switch ON
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
U158677E02
1.323,0.146 1.49,0.302 0.167,0.156 10 false *A 1.896,0.146 2.063,0.302 0.167,0.156 10 false *B 1.333,0.396 1.521,0.573 0.188,0.177 10 false 3E 1.917,0.396 2.094,0.573 0.177,0.177 10 false 3F 1.604,2.417 1.792,2.594 0.188,0.177 10 false 3B 0.156,0.094 0.323,0.25 0.167,0.156 10 false *a

a.

for LHD

i.

Disconnect the 3E and 3B instrument panel junction block assembly connectors.



b.

for RHD

i.

Disconnect the 3F and 3B instrument panel junction block assembly connectors.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-8 - Body ground Always Below 1 Ω


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION SWITCH)
U135109E02
1.594,0.156 1.802,0.313 0.208,0.156 10 false 3A 0.125,0.167 0.333,0.323 0.208,0.156 10 false *a

a.

Reconnect the instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-29 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(Instrument Panel Junction Block Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-40 - 3A-54 Always Below 1 Ω
3A-40 - Body ground Always 10 kΩ or higher




OK

5.REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MAIN BODY ECU
a.


NEXT

6.READ VALUE USING INTELLIGENT TESTER
6.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Ignition switch ON signal /
OFF or ON
OFF: Ignition switch ACC or off
ON: Ignition switch ON
-

OK:

Normal conditions listed above are displayed.




OK

END (MAIN BODY ECU WAS DEFECTIVE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY