Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.07–2017.01
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The meter CPU receives vehicle speed signals from the brake actuator assembly via the CAN communication system (CAN V1 Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly. The brake actuator assembly supplies power to the vehicle speed sensor. The brake actuator assembly detects vehicle speed signals based on the pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Vehicle Stability Control System (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).




WIRING DIAGRAM

E346310E02
0.115,3.156 1.74,3.563 1.625,0.406 10 false Brake Actuator Assembly (Skid Control ECU) 2.927,3.229 4.688,3.438 1.76,0.208 10 false : CAN Communication Line 5.292,3.156 7.156,3.354 1.865,0.198 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

CAUTION:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output A
CAN communication DTC is output B



A

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

B

2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160, 200 (km/h) Vehicle is stopped and the engine idling

OK:

Speedometer indication is normal.




OK

3.READ VALUE USING GTS (VEHICLE SPEED METER)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed/
Min.: 0 (0)
Max.: 255 (158)
Approximately same as actual vehicle speed (When vehicle is being driven) -

OK:

Vehicle speed displayed on the GTS is almost the same as the speedometer indication.




OK

4.CHECK VEHICLE STABILITY CONTROL SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK VEHICLE STABILITY CONTROL SYSTEM
a.

Check if a vehicle stability control DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
Vehicle stability control DTC is not output A
Vehicle stability control DTC is output B



A

REPLACE COMBINATION METER ASSEMBLY

B