Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is output when the combination meter assembly detects a fuel sender gauge malfunction.

DTC No. DTC Detection Condition Trouble Area
B1500 When combination meter detects fuel sender gauge malfunction
·

Harness or connector

·

Combination meter assembly

·

Fuel suction with pump and gauge tube assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

E219770E12
0.521,2.615 0.854,2.771 0.333,0.156 10 false K17 0.521,2.781 3.771,3.104 3.25,0.323 10 false Fuel Suction with Pump and Gauge Tube Assembly 3.531,1.219 3.781,1.375 0.25,0.156 10 false FS 3.531,1.604 3.76,1.76 0.229,0.156 10 false FE 2.49,1.208 2.708,1.365 0.219,0.156 10 false 2 3.844,1.219 4.063,1.375 0.219,0.156 10 false 2 2.479,1.594 2.698,1.75 0.219,0.156 10 false 1 3.844,1.604 4.063,1.76 0.219,0.156 10 false 3 5.188,1.333 5.406,1.49 0.219,0.156 10 false L 4.906,1.208 5.125,1.385 0.219,0.177 10 false 16 4.792,2.896 5.125,3.052 0.333,0.156 10 false F1 4.792,3.052 6.656,3.375 1.865,0.323 10 false Combination Meter Assembly 0.792,2.063 2.719,2.385 1.927,0.323 10 false Fuel Sender Gauge Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Combination Meter
Tester Display Test part Control Range Diagnostic Note
Fuel Meter Operation Fuel gauge EMPTY / 1/2 / FULL Vehicle is stopped and the engine idling

OK:

Fuel receiver gauge indication is normal.




OK

2.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel sender gauge input/
Min.: 0
Max.: 127.5
Fuel sender input value Unit: Liter

OK:

Fuel value displayed on the tester is approximately the same as needle indication.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
3.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.


E226985E01
0.894,3.002 1.052,3.168 0.158,0.166 10 E 0.894,1.307 1.052,1.473 0.158,0.166 10 F 1.43,2.056 1.661,2.223 0.231,0.166 10 1/2 2.222,2.796 2.772,2.962 0.550,0.166 10 Warning 0.26,0.135 0.418,0.301 0.158,0.166 10 *a


Text in Illustration
*a Component without harness connected
(Fuel Sender Gauge Assembly)
- -

b.

Check that the float moves smoothly between F and E.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Float Level Float Position (mm (in.)) Specified Condition
1 - 2 F 142 to 152 (5.591 to 5.984) 12.0 to 18.0 Ω
1/2 71.1 to 76.1 (2.799 to 2.996) 208.3 Ω
Warning 5.9 to 10.9 (0.232 to 0.429) 365.2 Ω
E 0 (0) 405.0 to 415.0 Ω


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C


d.

Reinstall the fuel sender gauge assembly.



A

4.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

4.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.
E158805E09
0.217,0.108 0.975,0.292 0.758,0.184 10 *a 2.507,0.547 2.753,0.710 0.246,0.163 10 FS 0.427,1.2 0.673,1.363 0.246,0.163 10 FE 1.355,1.278 0.745,1.278 false 1.836,1.217 2.425,0.629 false 0.615,0.656 1.411,0.821 0.796,0.165 10 *b 0.615,3.098 1.411,3.263 0.796,0.165 10 *c

Remove the fuel suction with pump and gauge tube assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-1 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Fuel Suction with Pump and Gauge Tube Assembly)
*b Connector A
*c Connector B

Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C


c.

Reinstall the fuel suction with pump and gauge tube assembly.



A

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)

B

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

C

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the K17 fuel suction with pump and gauge tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-16 (L) - K17-2 (FS) Always Below 1 Ω
F1-16 (L) - Body ground Always 10 kΩ or higher
K17-3 (FE) - Body ground Always Below 1 Ω



d.

Reconnect the fuel suction with pump and gauge tube assembly connector.


e.

Reconnect the combination meter assembly connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR