Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o VSC) › 2011.08–2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248315 AIRBAG SYSTEM(w/o VSC) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o VSC)  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

The DTCs are displayed by blinking the SRS warning light.

HINT:
·

Make sure that DTCs which relate to the CAN communication system are not output. If any of these DTCs are output, check the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(except Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).

·

When a warning light keeps blinking, a short to ground in the wiring of terminal TC of the DLC3 or an internal ground short in an ECU is suspected.

·

The DTC output mode signal is transmitted through the CAN to each ECU including the airbag sensor assembly. Thus if no systems enter DTC output mode, the ECM may have a malfunction.



WIRING DIAGRAM

C245075E01
1.446,2.502 1.867,2.658 0.421,0.156 10 A74 1.446,2.661 1.776,2.817 0.330,0.156 10 ECM 1.486,4.177 1.788,4.381 0.302,0.205 10 F4 1.486,4.359 1.913,4.522 0.427,0.163 10 DLC3 5.57,4.674 5.900,4.837 0.330,0.163 10 F16 5.57,4.849 7.125,5.026 1.555,0.177 10 Airbag Sensor Assembly 0.606,4.797 2.373,4.967 1.767,0.170 10 : CAN Communication Line 1.167,3.508 1.330,3.684 0.163,0.177 10 4 2.116,3.532 2.321,3.709 0.205,0.177 10 13 1.353,3.63 1.613,3.904 0.260,0.274 10 CG 1.825,3.63 2.197,3.856 0.371,0.225 10 TC 1.626,0.625 2.018,0.809 0.392,0.184 10 CANL 1.612,1.176 2.025,1.325 0.413,0.149 10 CANH 6.096,0.625 6.488,0.809 0.392,0.184 10 CANL 6.096,1.176 6.508,1.325 0.413,0.149 10 CANH 1.822,1.739 2.075,1.902 0.253,0.163 10 TC 2.141,0.437 2.768,0.614 0.627,0.177 10 49 2.141,1.005 2.845,1.182 0.704,0.177 10 41 2.141,1.579 2.870,1.763 0.729,0.184 10 27 5.827,0.483 6.076,0.657 0.248,0.174 10 22 5.808,1.043 6.085,1.282 0.276,0.239 10 13

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
U158312E02
1.823,0.917 2.135,0.167 2.135,0.167 2.365,0.167 true 1.969,2.667 2.448,2.854 true 2.396,0.063 2.615,0.229 0.219,0.167 10 false TC 0.156,0.115 0.344,0.281 0.188,0.167 10 false *1 0.354,0.677 0.635,0.854 0.281,0.177 10 false F4 0.198,1.604 0.365,1.781 0.167,0.177 10 false *a 0.365,2.667 0.635,2.833 0.271,0.167 10 false A74 2.5,2.771 3.01,2.948 0.51,0.177 10 false 27 (TC)

a.

Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-13 (TC) -
A74-27 (TC)
Always Below 1 Ω


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to ECM)



OK

2.CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)
a.
U158309E01
0.08,0.076 0.242,0.244 0.161,0.168 10 *1 1.376,1.821 1.611,1.969 0.234,0.148 10 CG 1.622,1.081 1.501,1.785 false 0.306,1.16 0.578,1.342 0.272,0.181 10 F4

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-4 (CG) -
Body ground
Always Below 1 Ω


Text in Illustration
*1 DLC3



OK

3.CHECK HARNESS AND CONNECTOR (TC OF ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TC OF ECM)
a.
U158313E02
2.052,1.063 2.531,1.469 true 0.125,0.177 0.323,0.333 0.198,0.156 10 false *a 0.427,1.063 0.698,1.229 0.271,0.167 10 false A74 2.563,1.396 3.073,1.552 0.51,0.156 10 false 27 (TC)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-27 (TC) -
Body ground
Always 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM
a.

Replace the ECM.


b.

Check for DTCs of the ECM.


Result
Result Proceed to
Normal code is output A
DTC is output (for 2NZ-FE) B
DTC is output (for 1NZ-FE) C
DTC output mode is set (except airbag sensor assembly) D



A

END

B

C

D