Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248319 FRONT PASSENGER AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Predisposal deployment may be considered hazardous material treatment.


HINT:

When scrapping a vehicle equipped with the SRS or disposing of a instrument panel passenger airbag assembly, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a instrument panel passenger airbag assembly that has an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (33 ft.) away from the instrument panel passenger airbag assembly.

·

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a instrument panel passenger airbag assembly a deployed airbag.

·

Do not apply water, etc. to a instrument panel passenger airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



PROCEDURE

Hide 73960A 1.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When Installed in Vehicle)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E05
1.788,1.612 2.188,1.814 0.4,0.201 10 SST 1.903,1.257 1.966,1.622 false 2.73,0.645 2.89,0.831 0.161,0.186 10 *1 2.715,0.739 2.521,0.739 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Text in Illustration
*1 Battery

SST
09082-00700  


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Remove the instrument cluster finish panel garnish assembly (See page INTERIOR PANELS/S TRIM > UPPER INSTRUMENT PANEL > REMOVAL).


d.

Install SST to the instrument panel wire inflator side.

i.
B282645E01
1.481,2.536 1.893,2.21 false 1.905,2.114 2.264,2.413 0.360,0.299 10 *1

Pull the slider in the direction indicated by the arrow to release the lock and disconnect the airbag connector.

Text in Illustration
*1 Slider

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



ii.

Connect SST connector to the instrument panel wire inflator side.

SST
09082-00700  
09082-00760  

NOTICE:
·

To avoid damaging SST connector and the wire harness, do not lock the secondary lock of the twin lock.

·

At this time, do not connect SST to the instrument panel wire actuator side.




iii.

Check that the lock slider is in the lock position.


iv.
B282646E02
1.375,1.302 1.75,1.354 true 1.781,1.302 2.104,1.51 0.323,0.208 10 true SST

Connect SST connector.

NOTICE:

Take care not to damage SST wire harness.



v.

Close all doors.


vi.
U134482E05
1.01,1.854 2.49,1.854 false 2.625,1.042 2.625,1.917 false 0.875,1.792 0.875,1.917 false 0.417,1.26 0.646,1.552 false 1.729,0.854 2.198,0.448 false 2.24,0.365 2.719,0.542 0.479,0.177 10 false *1 0.125,1.156 0.51,1.354 0.385,0.198 10 false SST 1.229,1.865 2.458,2.063 1.229,0.198 10 false 10 m or more

Move SST at least 10 m (33 ft.) away from the vehicle front side window.

Text in Illustration
*1 Battery



e.

Deploy the instrument panel passenger airbag assembly inflator.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Press SST activation switch and deploy the airbag.

CAUTION:
·

When deploying the airbag, make sure that no one is near the vehicle.

·

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a instrument panel passenger airbag assembly with a deployed airbag.

·

Do not apply water, etc. to a instrument panel passenger airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




Hide 73960A 2.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When not Installed in Vehicle)

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E01
2.098,0.656 2.43,0.857 0.332,0.201 10 SST 2.404,0.323 2.295,0.662 false

Check the function of SST.

SST
09082-00700  

CAUTION:

Always use the specified SST (SRS Airbag Deployment Tool) when deploying the airbag.


i.
B104820E05
1.788,1.612 2.188,1.814 0.4,0.201 10 SST 1.903,1.257 1.966,1.622 false 2.73,0.645 2.89,0.831 0.161,0.186 10 *1 2.715,0.739 2.521,0.739 false

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.

Text in Illustration
*1 Battery

SST
09082-00700  


ii.

Press the SST activation switch, and check that the LED on the SST activation switch illuminates.

CAUTION:
·

Do not connect the SST connector (yellow colored one) to the airbag.

·

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




iii.

Disconnect SST from the battery.



b.

Remove the instrument panel passenger airbag assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

Before removing the instrument panel passenger airbag assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.




c.

Connect SST.

i.
B286374E01
1.472,1.575 0.805,1.239 false 0.453,1.162 0.754,1.321 0.302,0.159 10 SST

Connect SST connector.


ii.
B286373E01
1.168,0.68 1.537,0.456 false 1.551,0.371 1.733,0.539 0.182,0.168 10 *1

Push in the locking button.

Text in Illustration
*1 Locking Button

NOTICE:
·

Securely lock the locking button.



SST
09082-00700  
09082-00802  (09082-10801, 09082-40800)



d.
B445426E01
1.552,1.667 1.854,1.208 false 1.365,1.563 1.563,1.74 0.198,0.177 10 false *a 2.844,0.969 3.042,1.146 0.198,0.177 10 false A

Using a braided wire harness, tie the instrument panel passenger airbag assembly to a tire.

Text in Illustration
*a Stripped Wire Harness Section

Stripped wire harness section:
Area Measurement
A 1.25 mm2 or more (0.00192 in.2 or more)


CAUTION:

If the wire harness is too thin or an alternative object is used to tie the instrument panel passenger airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the cross-sectional area of the stripped wire harness section:

Cross-sectional area = 3.14 x (Diameter)2 / 4


i.

Position the instrument panel passenger airbag assembly inside a tire with the airbag deployment side facing inside.

B285689E01
2.45,2.43 2.590,2.591 0.139,0.161 10 B 0.774,1.764 0.913,1.925 0.139,0.161 10 A

Tire size:
Area Measurement
A 360 mm (14.17 in.)
B 185 mm (7.28 in.)


CAUTION:
·

Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the instrument panel passenger airbag assembly may become loose due to the shock when the airbag is deployed.

·

Always tie down the instrument panel passenger airbag assembly with the airbag deployment side facing inside the tire.



NOTICE:

The tire will be marked by the airbag deployment, so use a waste tire.




e.
C106886E04
2.555,1.45 2.801,1.641 0.245,0.19 10 *1 2.55,0.297 2.796,0.488 0.245,0.19 10 *1

Place tires.

Text in Illustration
*1 Tires (2 or more)

i.

Place at least 2 tires under the tire which the instrument panel passenger airbag assembly is tied to.


ii.

Place at least 2 tires over the tire which the instrument panel passenger airbag assembly is tied to. The top tire should have a disc wheel installed.

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

As the disc wheel will be marked by the airbag deployment, use a waste disc wheel.

·

As the tires will be marked by the airbag deployment, use waste tires.




iii.
B105087

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.




f.

Install SST.

i.
C107076E21
1.615,1.698 1.396,1.698 false 0.438,2.427 0.302,2.573 false 1.667,1.625 1.885,1.823 0.219,0.198 10 false *1 0.135,2.594 0.448,2.74 0.313,0.146 10 false SST 1.021,2.594 2.208,2.792 1.188,0.198 10 false 10 m or more

Connect SST connector.

Text in Illustration
*1 Battery

SST
09082-00700  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness. Also, secure some slack for SST wire harness inside the tire.




g.

Deploy the instrument panel passenger airbag assembly inflator.

i.

Connect the red clip of SST to the positive battery terminal and the black clip of SST to the negative battery terminal.


ii.

Check that no one is within a 10 m (33 ft.) radius of the tire which the instrument panel passenger airbag assembly is tied to.


iii.

Press SST activation switch and deploy the airbag.

CAUTION:

Make sure that no one is near the tires when deploying the airbag.


HINT:

The airbag is deployed as the LED of SST activation switch comes on.



iv.

Disconnect the red clip of SST from the positive (+) battery terminal and the black clip of SST from the negative (-) battery terminal.



h.
C122262E01
2.086,0.906 2.392,0.73 false 2.403,0.622 2.555,0.782 0.152,0.161 10 *1

Dispose of the lower instrument panel passenger airbag assembly.

Text in Illustration
*1 Plastic Bag

CAUTION:
·

The lower instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a lower instrument panel passenger airbag assembly which has been deployed.

·

Do not apply water, etc. to a lower instrument panel passenger airbag assembly which has been deployed.

·

Always wash your hands with water after completing the operation.



i.

Remove the lower instrument panel passenger airbag assembly from the tire.


ii.

Place the lower instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.