Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(for 3 Door)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248321 CURTAIN SHIELD AIRBAG ASSEMBLY(for 3 Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(for 3 Door)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 63310 3.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62170A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

a.
B282648E01
0.87,2.437 0.57,2.617 false 0.409,2.548 0.569,2.700 0.160,0.151 10 *1 1.439,2.354 1.139,2.535 false 1.438,2.261 1.597,2.412 0.160,0.151 10 *2

Using a thin-bladed screwdriver with its tip wrapped with protective tape, release the locking button.

Text in Illustration
*1 Protective Tape
*2 Locking Button


b.

Disengage the airbag connector.


c.
C141263E16
1.427,0.75 1.083,0.167 1.083,0.167 0.948,0.167 false 2.25,0.385 2.448,0.167 2.448,0.167 2.542,0.167 false 2.396,1.104 2.594,0.885 2.594,0.885 2.688,0.885 false 0.99,1.333 0.792,1.677 0.792,1.677 0.688,1.677 false 0.781,0.104 0.979,0.271 0.198,0.167 10 false *1 2.594,0.094 2.844,0.292 0.25,0.198 10 false *2 2.719,0.802 2.969,1 0.25,0.198 10 false *3 0.521,1.604 0.74,1.792 0.219,0.188 10 false *4

Using a clip remover, pull up the 6 pins.

Text in Illustration
*1 Pin
*2 Clip
*3 Airbag
*4 Body Panel


d.
B235459E02
0.333,1.648 0.517,1.845 0.185,0.198 10 *2 0.436,1.114 0.436,1.641 false 2.563,1.661 2.760,1.837 0.198,0.177 10 *3 2.67,1.284 2.67,1.643 false 0.619,0.262 0.791,0.452 0.172,0.190 10 *1 1.078,0.489 0.945,0.357 0.945,0.357 0.791,0.357 false

Using needle-nose pliers, disengage each 2 claws to disconnect the 6 clips and curtain shield airbag from the body panel as shown in the illustration.

Text in Illustration
*1 Clip
*2 Airbag
*3 Body Panel


e.
B282649

Remove the bolt.


f.
B282650E03
2.948,1.177 2.698,1.813 true 1.208,1.26 0.958,1.885 true 2.573,1.823 2.75,1.969 0.177,0.146 10 false *1 0.833,1.896 1.01,2.042 0.177,0.146 10 false *2

Disengage hook A in the direction shown in the illustration, then disengage hook B by sliding in the direction shown in the illustration, and remove the curtain shield airbag assembly.

Text in Illustration
*1 Hook A
*2 Hook B


g.

Remove the 6 clips and 6 spacers from the curtain shield airbag assembly.

NOTICE:

If clips and spacers are removed, always replace them with new ones even though they may not appear to be damaged.