Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR(for 3 Door)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248327 SIDE AIRBAG SENSOR(for 3 Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for 3 Door)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Hide 69260 3.REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.
B271668

Insert a clip remover between the plate and front door trim board.


b.

Turn the handle with the clip remover inserted, as shown in the illustration.


c.

Remove the front door window regulator handle and clip.


d.

Remove the window regulator handle plate.


Hide 74231 4.REMOVE FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74231 5.REMOVE FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 67601 6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 89865 7.REMOVE DOOR SIDE AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B282656

Disconnect the connector from the door side airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push and hold the white housing lock, and slide the yellow outer connector locking sleeve.

C195226E24
3.927,1.313 3.927,2.146 false 1.385,1.313 1.385,2.146 false 1.135,0.99 1.135,0.531 1.135,0.531 1.052,0.531 true 3.656,1 3.656,0.542 3.656,0.542 3.573,0.542 true 0.875,1.729 1.063,1.896 0.188,0.167 10 false *a 3.417,1.75 3.813,1.958 0.396,0.208 10 false *a 0.906,0.458 1.094,0.635 0.188,0.177 10 false *1 3.417,0.469 3.604,0.646 0.188,0.177 10 false *1 1.302,2.156 1.49,2.333 0.188,0.177 10 false *2 3.854,2.156 4.042,2.333 0.188,0.177 10 false *2

Text in Illustration
*1 Housing Lock *2 Outer Connector Locking Sleeve
*a Slide - -


ii.

Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.



d.
B282657

Remove the bolt and door side airbag sensor.

NOTICE:

Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.