Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248330 AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag sensor assembly and front passenger airbag assembly.

The circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1805/52
·

The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Front passenger airbag assembly (Front passenger side squib)

·

Airbag sensor assembly


B1806/52
·

The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


B1807/52
·

The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction


B1808/52
·

The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C241679E03
0.403,3.652 0.600,3.815 0.198,0.163 10 S1 0.403,3.817 2.541,4.136 2.139,0.319 10 Front Passenger Airbag Assembly (Front Passenger Side Squib) 5.2,4.627 5.469,4.771 0.269,0.145 10 F16 5.283,3.152 5.452,3.315 0.169,0.163 10 P- 5.068,3.047 5.179,3.210 0.111,0.163 10 3 5.283,1.933 5.486,2.096 0.203,0.163 10 P+ 1.844,3.047 2.012,3.210 0.169,0.163 10 P- 1.809,1.828 2.012,1.991 0.203,0.163 10 P+ 5.068,1.828 5.179,1.991 0.111,0.163 10 4 2.091,3.047 2.202,3.210 0.111,0.163 10 1 2.091,1.828 2.202,1.991 0.111,0.163 10 2 3.48,2.942 3.591,3.105 0.111,0.163 10 2 3.48,1.723 3.591,1.886 0.111,0.163 10 1 3.405,1.929 3.708,2.092 0.303,0.163 10 FS1 3.407,3.134 3.710,3.297 0.303,0.163 10 FS1 5.2,4.805 6.765,4.975 1.565,0.170 10 Airbag Sensor Assembly

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C165139E12
2.119,2.18 2.278,2.345 0.158,0.165 10 *2 0.733,1.47 0.898,1.663 0.165,0.193 10 F 0.521,1.865 0.709,2.025 0.188,0.161 10 *1 1.478,0.252 1.676,0.405 0.199,0.152 10 *3 1.501,1.458 1.666,1.651 0.165,0.193 10 C 1.913,1.458 2.078,1.651 0.165,0.193 10 B 2.24,1.235 2.405,1.428 0.165,0.193 10 A 1.306,1.464 1.471,1.657 0.165,0.193 10 D 0.928,1.47 1.093,1.663 0.165,0.193 10 E 1.312,2.214 1.481,2.358 0.170,0.143 10 *4 0.636,1.403 0.636,1.855 false 1.561,2.289 1.767,1.403 false 1.419,0.317 1.153,1.257 false

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front passenger airbag assembly and airbag sensor assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the front passenger airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and No. 2 instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Passenger Airbag Assembly (Front Passenger Side Squib)
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire



OK

2.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
SST
09843-18061  

a.
U158428E01
0.876,0.582 0.986,0.734 0.109,0.153 10 F 1.073,0.582 1.194,0.734 0.121,0.153 10 E 1.439,0.582 1.559,0.734 0.121,0.153 10 D 1.573,0.582 1.694,0.734 0.121,0.153 10 C 0.606,0.853 0.757,0.995 0.151,0.142 10 *1 1.979,1.211 2.172,1.372 0.194,0.161 10 *2 0.609,1.469 0.786,1.609 0.177,0.140 10 *a 0.999,1.731 1.169,1.882 0.170,0.151 10 *3 2.499,2.191 2.787,2.349 0.288,0.158 10 SST 2.263,2.264 2.459,2.264 false 0.987,1.978 1.192,2.136 0.205,0.158 10 S1 0.696,0.822 0.808,0.507 false

Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the front passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Passenger Airbag Assembly (Front Passenger Side Squib)
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Front Passenger Airbag Assembly (Front Passenger Side Squib))



OK

NG

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
U158430E02
0.458,0.469 0.573,0.156 false 1.813,2.292 2.115,2.875 true 1.635,2.292 1.333,2.885 true 0.563,0.708 0.667,0.865 0.104,0.156 10 false F 2.115,0.458 2.24,0.615 0.125,0.156 10 false A 1.74,0.708 1.865,0.865 0.125,0.156 10 false B 0.76,0.708 0.885,0.865 0.125,0.156 10 false E 1.188,0.708 1.313,0.865 0.125,0.156 10 false D 1.323,0.708 1.448,0.865 0.125,0.156 10 false C 0.604,0.063 0.75,0.208 0.146,0.146 10 false *1 1.958,1.438 2.156,1.594 0.198,0.156 10 false *2 0.708,1.698 0.885,1.896 0.177,0.198 10 false *a 1.094,1.958 1.26,2.104 0.167,0.146 10 false *3 1.083,2.208 1.292,2.365 0.208,0.156 10 false S1 1.26,2.896 1.438,3.052 0.177,0.156 10 false P- 2.031,2.885 2.24,3.042 0.208,0.156 10 false P+

Disconnect SST from connector E.


d.

Disconnect the instrument panel wire from the airbag sensor assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S1-1 (P-) - Body ground Ignition switch ON Below 1 V
S1-2 (P+) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (P-) - S1-2 (P+) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (P-) - Body ground Always 1 MΩ or higher
S1-2 (P+) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (P-) - S1-2 (P+) Always 1 MΩ or higher


Text in Illustration
*1 Front Passenger Airbag Assembly (Front Passenger Side Squib)
*2 Airbag Sensor Assembly
*3 Connector E
*a Front view of wire harness connector
(to Front Passenger Airbag Assembly (Front Passenger Side Squib))




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front passenger airbag assembly and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
U158432E02
0.219,0.719 0.219,1.135 false 1.604,2.656 1.313,2.813 true 1.833,2.646 2.115,2.802 true 1.563,1.313 1.667,0.719 false 1.156,0.24 0.927,0.542 false 0.385,0.802 0.49,0.958 0.104,0.156 10 false F 0.615,0.802 0.74,0.958 0.125,0.156 10 false E 1.104,0.802 1.229,0.958 0.125,0.156 10 false D 1.344,0.802 1.469,0.958 0.125,0.156 10 false C 1.833,0.802 1.958,0.958 0.125,0.156 10 false B 2.25,0.521 2.375,0.677 0.125,0.156 10 false A 0.146,1.167 0.302,1.313 0.156,0.146 10 false *1 1.177,0.135 1.333,0.281 0.156,0.146 10 false *3 1.469,1.333 1.635,1.479 0.167,0.146 10 false *4 2.083,1.573 2.24,1.719 0.156,0.146 10 false *2 0.406,1.802 0.563,1.948 0.156,0.146 10 false *a 0.896,2.042 1.083,2.188 0.188,0.146 10 false *5 1.073,2.792 1.281,2.948 0.208,0.156 10 false P+ 2.156,2.792 2.333,2.948 0.177,0.156 10 false P- 0.865,2.323 1.135,2.5 0.271,0.177 10 false FS1

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the No. 2 instrument panel wire from the instrument panel wire.


c.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FS1-1 (P+) - Body ground Ignition switch ON Below 1 V
FS1-2 (P-) - Body ground Ignition switch ON Below 1 V




d.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FS1-1 (P+) - FS1-2 (P-) Always Below 1 Ω




e.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FS1-1 (P+) - Body ground Always 1 MΩ or higher
FS1-2 (P-) - Body ground Always 1 MΩ or higher




f.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FS1-1 (P+) - FS1-2 (P-) Always 1 MΩ or higher




g.

Restore the released activation prevention mechanism of connector B to the original condition.


Text in Illustration
*1 Front Passenger Airbag Assembly (Front Passenger Side Squib)
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*5 Connector C
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


OK

6.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
U158434E02
0.396,0.646 0.396,1.094 false 1.646,2.292 1.365,2.802 true 1.729,0.635 1.729,1.083 false 1.073,0.479 1.177,0.104 false 1.813,2.292 2.094,2.802 true 0.542,0.719 0.646,0.875 0.104,0.156 10 false F 0.792,0.708 0.917,0.865 0.125,0.156 10 false E 1.219,0.708 1.344,0.865 0.125,0.156 10 false D 1.479,0.708 1.604,0.865 0.125,0.156 10 false C 1.917,0.708 2.042,0.865 0.125,0.156 10 false B 2.302,0.458 2.427,0.615 0.125,0.156 10 false A 0.323,1.115 0.49,1.292 0.167,0.177 10 false *1 1.208,0.01 1.396,0.167 0.188,0.156 10 false *3 1.656,1.094 1.802,1.229 0.146,0.135 10 false *4 2.135,1.406 2.323,1.583 0.188,0.177 10 false *2 0.583,1.771 0.75,1.917 0.167,0.146 10 false *a 0.927,2.031 1.094,2.177 0.167,0.146 10 false *5 2.146,2.75 2.344,2.906 0.198,0.156 10 false P+ 1.167,2.75 1.365,2.906 0.198,0.156 10 false P- 0.927,2.302 1.115,2.479 0.188,0.177 10 false S1

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S1-1 (P-) - Body ground Ignition switch ON Below 1 V
S1-2 (P+) - Body ground Ignition switch ON Below 1 V




b.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (P-) - S1-2 (P+) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (P-) - Body ground Always 1 MΩ or higher
S1-2 (P+) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S1-1 (P-) - S1-2 (P+) Always 1 MΩ or higher




e.

Restore the released activation prevention mechanism of connector D to the original condition.


Text in Illustration
*1 Front Passenger Airbag Assembly (Front Passenger Side Squib)
*2 Airbag Sensor Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*5 Connector E
*a Front view of wire harness connector
(to Front Passenger Airbag Assembly (Front Passenger Side Squib))


OK

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE