Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248330 AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the airbag sensor assembly and the lower No. 1 instrument panel airbag assembly.

This circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1860/64
·

The airbag sensor assembly receives a line short circuit signal in the driver side knee airbag squib circuit during primary check.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee airbag squib)

·

Airbag sensor assembly


B1861/64
·

The airbag sensor assembly receives an open circuit signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


B1862/64
·

The airbag sensor assembly receives a short circuit to ground signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction


B1863/64
·

The airbag sensor assembly receives a short circuit to B+ signal in the driver side knee airbag squib circuit.

·

Driver side knee airbag squib malfunction

·

Airbag sensor assembly malfunction



WIRING DIAGRAM

C222225E20
4.437,2.116 4.544,2.265 0.107,0.148 10 9 2.726,2.12 2.822,2.262 0.096,0.142 10 1 2.726,2.959 2.837,3.108 0.111,0.149 10 2 4.397,2.962 4.586,3.105 0.189,0.143 10 10 4.698,2.21 5.037,2.363 0.339,0.154 10 DK+ 4.698,3.044 5.009,3.221 0.311,0.177 10 DK- 1.046,3.558 1.318,3.725 0.272,0.167 10 F19 1.046,3.716 4.033,4.039 2.987,0.323 10 Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib) 4.598,4.674 4.865,4.817 0.267,0.143 10 F16 4.598,4.831 6.152,4.982 1.554,0.151 10 Airbag Sensor Assembly 2.292,2.114 2.593,2.267 0.301,0.154 10 DK+ 2.292,2.962 2.582,3.104 0.290,0.142 10 DK-

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
C167985E31
0.865,1.271 0.865,2.125 false 1.375,0.688 1.469,1.125 false 0.958,1.354 1.083,1.51 0.125,0.156 10 false D 1.156,1.354 1.281,1.51 0.125,0.156 10 false C 1.552,1.354 1.677,1.51 0.125,0.156 10 false B 1.885,1.104 2.01,1.26 0.125,0.156 10 false A 0.802,2.146 0.979,2.302 0.177,0.156 10 false *1 1.219,0.563 1.375,0.708 0.156,0.146 10 false *3 2.083,1.979 2.281,2.146 0.198,0.167 10 false *2

Check that the connectors are properly connected to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib)
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire



OK

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB)
SST
09843-18061  

a.
U158506E02
2.604,2.271 2.927,2.271 false 0.917,0.688 0.917,1.156 false 1.031,0.771 1.156,0.927 0.125,0.156 10 false D 1.219,0.771 1.344,0.927 0.125,0.156 10 false C 0.865,1.167 1.052,1.323 0.188,0.156 10 false *1 1.625,1.396 1.802,1.563 0.177,0.167 10 false *2 1,1.552 1.167,1.698 0.167,0.146 10 false *a 1.188,1.917 1.365,2.063 0.177,0.146 10 false *3 2.969,2.188 3.26,2.344 0.292,0.156 10 false SST 1.156,2.188 1.417,2.365 0.26,0.177 10 false F19

Connect the connector to the airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the lower No. 1 instrument panel airbag assembly (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib)
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib))

HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and 64B1863/64 may be output at this time, but they are not related to this check.




OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT)
3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
U158507E02
0.573,0.625 0.573,1.094 false 1.927,2.271 1.625,2.594 false 2.156,2.271 2.427,2.583 false 1.927,2.271 1.625,2.594 true 2.146,2.26 2.417,2.573 true 1.25,0.438 1.333,0.146 false 0.719,0.729 0.844,0.885 0.125,0.156 10 false D 0.979,0.729 1.104,0.885 0.125,0.156 10 false C 1.49,0.729 1.615,0.885 0.125,0.156 10 false B 1.906,0.469 2.031,0.625 0.125,0.156 10 false A 0.5,1.115 0.667,1.292 0.167,0.177 10 false *1 1.365,0.042 1.552,0.198 0.188,0.156 10 false *3 1.74,1.531 1.906,1.708 0.167,0.177 10 false *2 0.792,1.49 0.958,1.646 0.167,0.156 10 false *a 1.083,1.781 1.271,1.927 0.188,0.146 10 false *4 1.302,2.531 1.625,2.688 0.323,0.156 10 false DK+ 2.479,2.51 2.76,2.667 0.281,0.156 10 false DK- 1.073,2.094 1.333,2.271 0.26,0.177 10 false F19

Disconnect SST from connector C.


d.

Disconnect the instrument panel wire from the airbag sensor assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F19-1 (DK+) - Body ground Ignition switch ON Below 1 V
F19-2 (DK-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-1 (DK+) - F19-2 (DK-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-1 (DK+) - Body ground Always 1 MΩ or higher
F19-2 (DK-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-1 (DK+) - F19-2 (DK-) Always 1 MΩ or higher


Text in Illustration
*1 Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib)
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Connector C
*a Front view of wire harness connector
(to Lower No. 1 Instrument Panel Airbag Assembly (Driver Side Knee Airbag Squib))




OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the lower No. 1 instrument panel airbag assembly and airbag sensor assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ VSC/Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

OK:

DTC B1860/64, B1861/64, B1862/64 or B1863/64 is not output.


HINT:

Codes other than DTCs B1860/64, B1861/64, B1862/64 and B1863/64 may be output at this time, but they are not related to this check.




OK

NG