Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)
RM19S0E _58 Vehicle Interior _051497 SEAT BELT _0248339 FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door) N

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:

When scrapping a vehicle equipped with the SRS or disposing of a steering pad, deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of the DISTRIBUTOR.


CAUTION:
·

Never dispose of a front seat outer belt that has an inactivated pretensioner.

·

The seat belt pretensioner produces a loud, exploding sound when it activates. Perform the operation outside and where it will not be a nuisance to persons nearby.

·

When activating a front seat outer belt (with seat belt pretensioner), stand at least 10 m (33 ft.) away from the front seat outer belt.

·

Use gloves and safety glasses when handling a front seat outer belt with an activated pretensioner.

·

Always wash your hands with water after completing the activation.

·

Do not apply water to a front seat outer belt that has an activated pretensioner.

·

When activating the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool).

·

Perform the operation in a place away from electrical interference.

·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.



HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 73210 1.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE)

HINT:

Prepare a battery as the power source to activate the seat belt pretensioner.


a.
B104819E13
2.406,0.375 2.292,0.719 false 2.094,0.719 2.427,0.917 0.333,0.198 10 false SST

Check whether SST is functioning.

SST
09082-00700  

CAUTION:

Always use the specified SST when activating the seat belt pretensioner.


i.
B104820E24
1.906,1.313 1.969,1.677 false 2.521,0.76 2.75,0.76 false 2.75,0.677 2.896,0.896 0.146,0.219 10 false *1 1.833,1.698 2.229,1.896 0.396,0.198 10 false SST

Connect the SST red clip to the positive battery terminal and the black clip to the negative battery terminal.

Text in Illustration
*1 Battery

HINT:

Do not connect the yellow connector. The yellow connector is for connections to the seat belt pretensioner.



ii.
B104821E12
2.417,1.583 2.469,1.74 false 2.396,1.75 2.729,1.948 0.333,0.198 10 false SST

Press the SST activation switch and check that the LED of the SST activation switch turns on.

CAUTION:

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




b.

Disconnect SST from the battery.


c.

Disconnect the pretensioner connector.

i.

Remove the front quarter trim panel assembly (See page Vehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY(for 5 Door)>REMOVAL).


ii.
B282672E01
0.722,1.68 1.001,1.556 false 1.009,1.472 1.169,1.635 0.160,0.162 10 *1 0.615,2.073 0.544,1.717 false 0.514,2.066 0.674,2.228 0.160,0.162 10 *2 0.629,1.682 0.7,1.646 false 0.647,1.699 0.728,1.653 false 0.674,1.709 0.755,1.663 false 0.686,1.721 0.768,1.676 false 0.713,1.725 0.795,1.68 false 0.732,1.738 0.813,1.693 false 0.753,1.741 0.834,1.695 false 0.785,1.744 0.866,1.698 false 0.824,1.752 0.897,1.714 false

Disconnect the pretensioner connector.

Text in Illustration
*1 Protective Tape
*2 Locking Button

1.

Using a screwdriver with its tip wrapped in protective tape, release the locking button.

2.

Disconnect the pretensioner connector.




d.
B293018E01
1.125,1.884 0.666,1.666 false 0.317,1.572 0.610,1.731 0.294,0.158 10 SST 1.004,3.011 1.457,2.875 false 1.479,2.777 1.642,2.941 0.162,0.164 10 *1

Connect SST.

Text in Illustration
*1 Locking Button

i.

Connect SST, then the yellow connector to the seat belt pretensioner.

SST
09082-00770  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.
U134482E04
1.01,1.854 2.49,1.854 false 2.604,1.073 2.604,1.948 false 0.865,1.844 0.865,1.969 false 0.417,1.26 0.646,1.552 false 1.719,0.896 2.188,0.49 false 2.198,0.333 2.677,0.51 0.479,0.177 10 false *1 0.146,1.115 0.531,1.313 0.385,0.198 10 false SST 1.229,1.885 2.458,2.083 1.229,0.198 10 false 10 m or more

Move SST at least 10 m (33 ft.) away from the front of the vehicle.

Text in Illustration
*1 Battery

SST
09082-00700  


iii.

Close the doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.


HINT:

Do not close the windows fully. Leave a gap for inserting the SST wire harness.



iv.

Connect the SST red clip to the positive battery terminal and the black clip to the negative battery terminal.



e.

Activate the seat belt pretensioner.

i.

Confirm that no one is inside the vehicle or within 10 m (33 ft.) of the vehicle.


ii.

Press the SST activation switch and activate the seat belt pretensioner.

HINT:

The seat belt pretensioner operates simultaneously with the SST activation switch LED light.




f.

Disconnect SST.


g.

Dispose of the front seat outer belt (with the seat belt pretensioner).

HINT:

When scrapping a vehicle, activate the seat belt pretensioner, and then scrap the vehicle with the activated front seat outer belt still installed.


CAUTION:
·

Do not touch the front seat outer belt for at least 30 minutes after the seat belt pretensioner has been activated. It is very hot.

·

Use gloves and safety glasses when handling a front seat outer belt with a pretensioner that has been activated.

·

Always wash your hands with water after completing the operation.

·

Do not apply water to a front seat outer belt that has an activated pretensioner.




Hide 73210 2.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

HINT:

Prepare a battery as the power source to activate the seat belt pretensioner.


NOTICE:
·

When only disposing of the front seat outer belt (with the seat belt pretensioner), never use the customer's vehicle to activate the seat belt pretensioner.

·

Be sure to follow the procedures described below when activating the seat belt pretensioner.



a.

Remove the front seat outer belt assembly (See page Vehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)>REMOVAL).


b.
B272839E01
1.875,0.304 1.328,0.088 false 1.144,0 1.344,0.148 0.200,0.148 10 *a 2.349,0.384 2.769,0.546 0.420,0.162 10 10 cm

Wind the seat belt with the retractor.

Text in Illustration
*a Cut


c.

When the seat belt is sufficiently wound, cut the seat belt approximately 10 cm (0.328 ft.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the seat belt is wound.



d.
B104819E13
2.406,0.375 2.292,0.719 false 2.094,0.719 2.427,0.917 0.333,0.198 10 false SST

Check whether SST is functioning.

SST
09082-00700  

CAUTION:

Always use the specified SST when activating the seat belt pretensioner.


i.
B104820E24
1.906,1.313 1.969,1.677 false 2.521,0.76 2.75,0.76 false 2.75,0.677 2.896,0.896 0.146,0.219 10 false *1 1.833,1.698 2.229,1.896 0.396,0.198 10 false SST

Connect the SST red clip to the positive battery terminal and the black clip to the negative battery terminal.

Text in Illustration
*1 Battery

HINT:

Do not connect the yellow connector. The yellow connector is for connections to the seat belt pretensioner.



ii.
B104821E12
2.417,1.583 2.469,1.74 false 2.396,1.75 2.729,1.948 0.333,0.198 10 false SST

Press the SST activation switch and check that the LED of the SST activation switch turns on.

CAUTION:

If the LED illuminates when the activation switch is not being pressed, SST may be malfunctioning. Do not use SST.




e.
B293018E01
1.125,1.884 0.666,1.666 false 0.317,1.572 0.610,1.731 0.294,0.158 10 SST 1.004,3.011 1.457,2.875 false 1.479,2.777 1.642,2.941 0.162,0.164 10 *1

Connect SST.

Text in Illustration
*1 Locking Button

i.

Connect SST, then the yellow connector to the seat belt pretensioner.

SST
09082-00770  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.
B445431E01
1.917,1.573 1.99,1.25 false 1.813,1.583 2.125,1.781 0.313,0.198 10 false *a 2.979,1.01 3.292,1.208 0.313,0.198 10 false A

Using a service-purpose wire harness for the vehicle, tie the seat belt pretensioner to the tire with a wheel attached.

Text in Illustration
*a Stripped Wire Harness Section

Stripped wire harness section:
Area Measurement
A 1.25 mm2 or more (0.0019 in.2 or more)


CAUTION:
·

Do not use wire harnesses that are too thin or any other object to tie the seat belt pretensioner because they may snap due to the shock when the pretensioner is deployed.

·

Always use a wire harness for vehicle use, with a cross section of at least 1.25 mm2 (0.0019 in.2).



HINT:

To calculate the area of the stripped wire harness cross section:

Area = 3.14 x (Diameter)2 divided by 4


NOTICE:

The tire will be marked by the pretensioner deployment, so use a waste tire.



iii.
B282677E02
2.245,0.96 2.567,1.130 0.323,0.170 10 SST 1.986,1.055 2.23,1.055 false 1.342,2.333 1.09,1.669 1.09,1.669 1.972,2.343 false 0.908,1.547 1.085,1.716 0.177,0.170 10 *1

Connect SST.

Text in Illustration
*1 Wire Harness

SST
09082-00700  

NOTICE:
·

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.

·

Set up the front seat outer belt, as shown in the illustration.




iv.
B282678E01
0.618,4.221 0.940,4.387 0.322,0.166 10 SST 0.659,4.113 0.767,4.221 false 1.958,3.993 2.840,4.157 0.882,0.163 10 10 m or more 1.659,1.097 1.97,1.001 false 1.981,0.906 2.911,1.168 0.930,0.263 10 *1

Move SST at least 10 m (33 ft.) away from the wheel.

Text in Illustration
*1 Battery

NOTICE:

Take care not to damage the SST wire harness.




f.

Activate the seat belt pretensioner.

i.

Connect the SST red clip to the positive battery terminal and the black clip to the negative battery terminal.


ii.

Check that no one is within 10 m (33 ft.) of the wheel.


iii.

Press the SST activation switch and activate the seat belt pretensioner.

HINT:

The seat belt pretensioner operates simultaneously with the SST activation switch LED light.




g.

Disconnect SST.


h.
B282679E01
2.102,0.638 2.417,0.499 false 2.423,0.408 2.582,0.566 0.159,0.159 10 *1

Dispose of the front seat outer belt (with the seat belt pretensioner).

Text in Illustration
*1 Plastic Bag

CAUTION:
·

Do not touch the front seat outer belt for at least 30 minutes after the seat belt pretensioner has been activated. It is very hot.

·

Use gloves and safety glasses when handling a front seat outer belt with a pretensioner that has been activated.

·

Always wash your hands with water after completing the operation.

·

Do not apply water to a front seat outer belt that has an activated pretensioner.



i.

Place the front seat outer belt in a plastic bag, tie the end tightly and dispose of it according to local regulations.