Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2014.07–2017.10
RM19S0E _58 Vehicle Interior _051497 SEAT BELT _0248348 SEAT BELT WARNING SYSTEM U

SEAT BELT  SEAT BELT WARNING SYSTEM  TERMINALS OF ECU  


CHECK COMBINATION METER ASSEMBLY


U158625E02
2.198,0.469 2.438,0.646 0.24,0.177 10 false F1 5.135,0.469 5.375,0.646 0.24,0.177 10 false F3

a.

Disconnect the F1 combination meter assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-40 (B) - Body ground L - Body ground Combination meter +B line Always 11 to 14 V
F1-39 (IG+) - Body ground P - Body ground Combination meter IG line Ignition switch ON 11 to 14 V
F1-21 (ET) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the F1 combination meter assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-7 (P/SB) - Body ground P - Body ground Front passenger seat belt signal Front passenger seat occupied, seat belt fastened Below 1 V
Front passenger seat occupied, seat belt unfastened 11 to 14 V

If the result is not as specified, the meter may have a malfunction.



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U158580E02
1.021,0.958 1.219,1.104 0.198,0.146 10 false 3D 0.302,0.177 0.448,0.323 0.146,0.146 10 false *1 0.958,6.74 1.125,6.896 0.167,0.156 10 false *2 1.542,3.875 1.74,4.021 0.198,0.146 10 false 3D 3.823,0.802 4.052,0.969 0.229,0.167 10 false MB 3.823,2.885 4.052,3.042 0.229,0.156 10 false MB 1.021,1.594 1.219,1.75 0.198,0.156 10 false 3C 4.021,3.865 4.229,4.01 0.208,0.146 10 false 3C 6.406,0.969 6.604,1.115 0.198,0.146 10 false 3B 6.406,1.604 6.604,1.75 0.198,0.146 10 false 3A 5.49,5.24 5.688,5.385 0.198,0.146 10 false 3A 3.792,6.479 4.052,6.625 0.26,0.146 10 false F76 3.698,7.521 3.969,7.667 0.271,0.146 10 false F76 1.708,5.25 1.906,5.396 0.198,0.146 10 false 3B 1.021,2.125 1.219,2.281 0.198,0.156 10 false 3F 6.365,3.875 6.552,4.021 0.188,0.146 10 false 3F 0.479,2.135 0.677,2.292 0.198,0.156 10 false 3E 5.802,3.865 6,4.021 0.198,0.156 10 false 3E 5.813,3.625 5.979,3.781 0.167,0.156 10 false *A 6.375,3.625 6.542,3.781 0.167,0.156 10 false *B 0.49,1.906 0.656,2.063 0.167,0.156 10 false *A 1.031,1.906 1.198,2.063 0.167,0.156 10 false *B

Text in Illustration
*A for LHD *B for RHD
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-2 (FLCY) - Body ground - Front door courtesy light switch LH signal Front door LH open Below 1 Ω
Front door LH closed 10 kΩ or higher
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-29 (ACC) - Body ground - Ignition power supply Ignition switch ACC 11 to 14 V
MB-30 (BECU) - Body ground - Battery (ECU power source) Always 11 to 14 V
MB-31 (ALTB) - Body ground - Battery (ECU power source) Always 11 to 14 V
MB-32 (IG) - Body ground - Ignition power supply Ignition switch ON 11 to 14 V
F76-19 (FRCY) - Body ground Y - Body ground Front door courtesy light switch RH signal Front door RH open Below 1 Ω
Front door RH closed 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Install the main body ECU to the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


d.

Measure the voltage and check for pulse according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3D-34 (DBKL) - Body ground W - Body ground Driver seat belt warning signal Driver seat belt fastened 11 to 14 V
Driver seat belt unfastened Below 1 V
F76-13 (CANL) - Body ground W - Body ground CAN communication line Ignition switch ON Pulse generation
F76-14 (CANH) - Body ground R - Body ground CAN communication line Ignition switch ON Pulse generation

If the result is not as specified, the main body ECU may have a malfunction.