Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.07–2015.06
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248350 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1411/11  Room Temperature Sensor Circuit  


DESCRIPTION

The cooler thermistor (room temperature sensor) for the front seat is installed in the instrument panel to detect the room temperature and control the heater and air conditioner auto mode. The resistance of the room temperature sensor changes in accordance with the front room temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the room temperature sensor and reads voltage changes as the resistance of the room temperature sensor changes. This sensor also sends the appropriate signals to the air conditioning amplifier assembly.

DTC No. DTC Detection Condition Trouble Area
B1411/11 An open or short in the cooler thermistor (room temperature sensor) circuit.
·

Cooler thermistor (room temperature sensor)

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E346158E01
2.458,0.74 2.594,0.948 0.135,0.208 10 false 1 2.458,1.167 2.594,1.375 0.135,0.208 10 false 2 0.833,1.823 1.094,2.021 0.26,0.198 10 false F33 0.844,1.99 2.406,2.323 1.563,0.333 10 false Cooler Thermistor (Room Temperature Sensor) 4.948,0.75 5.115,0.948 0.167,0.198 10 false 29 4.948,1.156 5.125,1.365 0.177,0.208 10 false 34 5.26,0.906 5.427,1.104 0.167,0.198 10 false TR 5.271,1.302 5.625,1.49 0.354,0.188 10 false SG-1 4.646,2.063 4.906,2.26 0.26,0.198 10 false F42 4.635,2.25 6.833,2.448 2.198,0.198 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Room Temperature Sensor Room temperature sensor /
Min.: -6.5°C (20.3°F)
Max.: 57.25°C (135.1°F)
Actual room temperature is displayed -

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.INSPECT COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
3.INSPECT COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
a.

Inspect the cooler thermistor (room temperature sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>ROOM TEMPERATURE SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

4.CHECK HARNESS AND CONNECTOR (COOLER THERMISTOR (ROOM TEMPERATURE SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F33 cooler thermistor (room temperature sensor) connector.


b.

Disconnect the F42 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-1 - F42-29 (TR) Always Below 1 Ω
F33-2 - F42-34 (SG-1) Always Below 1 Ω
F33-1 - Body ground Always 10 kΩ or higher
F33-2 - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR