The No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix servo motor to any position. As a result, the air mix servo motor varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air is as requested.
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1441/41 | The air mix damper position does not change when the air conditioning amplifier assembly operates the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor). | ·
No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse (D) | Air mix servo motor target pulse /
Min.: 0 Max.: 255 |
·
MAX COOL: 4 (pulse) ·
MAX HOT: 93 (pulse) |
- |
| Air Mix Servo Actual Pulse (D) | Air mix servo motor actual pulse /
Min.: 0 Max.: 255 |
Follows the target pulse | - |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| OK (When troubleshooting according to the DTC) | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| NG | C |
A
B
C
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1441/41 is not output
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse (D) | Air mix servo motor pulse | Min.: 0, Max.: 255 | Perform Active Test when value between 4 and 93 displayed |
No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) operates normally.
OK
NG
Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).
Since the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) cannot be inspected while it is removed from the vehicle, replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix servo motor) with a new or normally functioning one.
NEXT
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1441/41 is not output
OK
NG
Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
NEXT
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1441/41 is not output
OK
NG