Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248350 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1442/42  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet servo motor) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet servo motor to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC No. DTC Detection Condition Trouble Area
B1442/42 The air inlet servo motor position does not change when the air conditioning amplifier assembly operates the No. 1 blower damper servo sub-assembly (air inlet servo motor).
·

No. 1 blower damper servo sub-assembly (air inlet servo motor)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E228241E02
5.546,1.929 6.765,2.243 1.219,0.314 10 Air Conditioning Amplifier Assembly 3.424,1.915 4.603,2.250 1.179,0.334 10 Air Conditioning Harness Assembly 5.542,1.787 5.722,1.943 0.180,0.156 10 z4 0.174,1.829 2.880,2.173 2.706,0.343 10 No. 1 Blower Damper Servo Sub-Assembly (Air Inlet Servo Motor) 5.3,0.322 5.404,0.486 0.104,0.164 10 4 5.511,0.396 5.937,0.560 0.426,0.164 10 BBUS 3.015,0.92 3.198,1.084 0.183,0.164 10 IC 5.511,1.429 5.937,1.593 0.426,0.164 10 BUSG 5.3,1.353 5.404,1.517 0.104,0.164 10 2 5.511,0.911 5.819,1.075 0.307,0.164 10 BUS 5.297,0.835 5.404,0.999 0.107,0.164 10 3

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Targ Pulse Air inlet servo motor target pulse /
Min.: 0
Max.: 255
·

Recirculation: 6 (pulse)

·

Fresh: 22 (pulse)


-
Air Inlet Damper Actual Pulse Air inlet servo motor actual pulse /
Min.: 0
Max.: 255
Follows the target pulse -

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Inlet Damper Targ Pulse Air inlet damper target pulse Min.: 0, Max.: 255 Perform Active Test when value between 6 and 22 displayed

OK:

No. 1 blower damper servo sub-assembly (air inlet servo motor) operates normally.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

4.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR)
4.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR)
a.

Replace the No. 1 blower damper servo sub-assembly (air inlet servo motor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the No. 1 blower damper servo sub-assembly (air inlet servo motor) cannot be inspected while it is removed from the vehicle, replace the No. 1 blower damper servo sub-assembly (air inlet servo motor) with a new or normally functioning one.




NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET SERVO MOTOR) IS FAULTY)

NG

6.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
6.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY