Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.07–2015.06
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248350 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14A2  Driver Side Solar Sensor Short Circuit  


DESCRIPTION

E132508E19
0.406,0.25 2.396,0.5 1.99,0.25 10 false Output Current of Photodiode 0.354,0.854 0.813,1.104 0.458,0.25 10 false High 0.365,2.5 0.823,2.771 0.458,0.271 10 false Low 0.813,2.708 1.333,2.958 0.521,0.25 10 false Weak 2.156,2.677 2.708,2.948 0.552,0.271 10 false Strong 0.802,3.01 2.542,3.25 1.74,0.24 10 false Strength of Solar Radiation

The automatic light control sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the automatic light control sensor varies according to the amount of sunlight. When the amount of sunlight increases, the output current increases. As the amount of sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects the output current from the automatic light control sensor.

DTC No. DTC Detection Condition Trouble Area
B14A2 A short in the driver side solar sensor circuit.
·

Automatic light control sensor

·

Harness or connector

·

Main body ECU

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E231123E01
1.531,0.966 1.905,1.113 0.373,0.147 10 CLTB 1.517,1.551 1.905,1.702 0.387,0.151 10 CLTE 2.036,0.884 2.136,1.031 0.100,0.147 10 3 2.036,1.469 2.150,1.611 0.114,0.142 10 5 2.036,2.97 2.143,3.123 0.107,0.154 10 1 1.599,3.047 1.906,3.198 0.306,0.151 10 TSD 0.453,3.413 0.738,3.583 0.286,0.170 10 F73 0.453,3.582 2.409,3.733 1.957,0.151 10 Automatic Light Control Sensor 5.142,3.047 5.464,3.198 0.322,0.151 10 TSD 4.871,2.966 5.054,3.127 0.184,0.161 10 33 5.104,3.446 5.376,3.602 0.272,0.156 10 F42 5.104,3.6 6.311,3.918 1.207,0.318 10 Air Conditioning Amplifier Assembly 5.081,1.541 5.459,1.713 0.378,0.172 10 CLTE 5.081,0.957 5.461,1.122 0.380,0.165 10 CLTB 4.81,0.876 4.994,1.039 0.184,0.163 10 20 4.801,1.467 4.993,1.614 0.193,0.147 10 22 5.151,1.97 5.425,2.115 0.274,0.144 10 F76 5.151,2.143 6.163,2.308 1.012,0.165 10 Main Body ECU

CAUTION / NOTICE / HINT

HINT:

If DTC B1244 is output together with other DTCs, troubleshoot DTC B1244 first (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>B1244).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor (D side) Driver side solar sensor /
Min.: 0
Max.: 255
Driver side solar sensor value increases as brightness increases -

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

2.CHECK FOR DTC

B

C

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U158593E01
0.588,1.045 0.844,1.226 0.256,0.181 10 F73 0.071,0.043 0.241,0.203 0.170,0.161 10 *a 0.681,0.573 1.059,0.720 0.378,0.147 10 CLTB 2.288,1.392 2.671,1.548 0.383,0.156 10 CLTE 1.563,1.171 1.128,0.653 false 1.871,1.336 2.268,1.478 false

a.

Disconnect the F73 automatic light control sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F73-3 (CLTB) - F73-5 (CLTE) Ignition switch off Below 1 V
F73-3 (CLTB) - F73-5 (CLTE) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Automatic Light Control Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
4.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F73 automatic light control sensor connector.


b.

Disconnect the F42 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-1 (TSD) - F42-33 (TSD) Always Below 1 Ω
F73-1 (TSD) - Body ground Always 10 kΩ or higher




OK

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR
U158594E01
0.588,0.865 0.845,1.046 0.256,0.181 10 F73 0.067,0.071 0.237,0.231 0.170,0.161 10 *a 0.488,1.384 0.873,1.540 0.385,0.156 10 CLTE 2.504,0.654 2.819,0.810 0.316,0.156 10 TSD 2.465,0.74 1.932,0.873 false 0.944,1.466 1.507,1.294 false

a.

Remove the automatic light control sensor (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Reconnect the automatic light control sensor connector.


c.

Reconnect the air conditioning amplifier assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F73-1 (TSD) - F73-5 (CLTE) Ignition switch ON
Sensor subjected to electric light
0.8 to 4.3 V
F73-1 (TSD) - F73-5 (CLTE) Ignition switch ON
Sensor covered with cloth
Below 0.8 V


Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)

NOTICE:

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 5 and the positive (+) lead to terminal 1 of the automatic light control sensor.


HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the automatic light control sensor.

·

As the inspection light is moved away from the sensor, the voltage decreases.





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

6.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
a.

Disconnect the F73 automatic light control sensor connector.


b.

Disconnect the F76 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-3 (CLTB) - F76-20 (CLTB) Always Below 1 Ω
F73-5 (CLTE) - F76-22 (CLTE) Always Below 1 Ω
F73-3 (CLTB) - Body ground Always 10 kΩ or higher
F73-5 (CLTE) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR