Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for 5 Door) › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051500 INTERIOR PANELS / TRIM _0248378 ROOF HEADLINING(for 5 Door) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for 5 Door)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ROOF HEADLINING ASSEMBLY

a.
B284352

Pull the roof headlining back into the vehicle through the back door.

NOTICE:

Do not damage the roof headlining assembly or body interior.



b.

Engage the 2 hooks and install the roof headlining.


c.

Install the 3 clips.


d.

Engage the 2 claws.


e.

for front pillar RH side:

i.

Engage the 4 clamps.


ii.

Connect the connector.



f.

for front pillar LH side:

i.

Engage the 4 clamps.


ii.

Connect the connector.



g.

for rear pillar RH side:

i.

Engage the 3 clamps.


ii.

Connect the connector.



Hide 73350C 2.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

a.

Install the rear center seat outer belt with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Engage the 2 claws and close the slip joint cover.


Hide 74610S 4.INSTALL ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure to install all assist grips.


a.

Engage the 2 clips and install the assist grip.


b.
B114352

Engage the 4 claws and install the 2 assist grip covers.


Hide 63339A 5.INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/ Cover)

HINT:

Use the same procedure to install all roof headlining service hole covers.


a.

Install the 2 roof headlining service hole covers.


Hide 74348 6.INSTALL VISOR HOLDER

a.
B170213E02
0.973,2.695 1.210,2.845 0.237,0.150 10 45°

Engage the 2 claws and turn the visor holder counterclockwise 45° to install it.

HINT:

Use the same procedure for the RH side and LH side.



Hide 74310 7.INSTALL VISOR ASSEMBLY RH

a.

Install the visor with the 2 screws.


b.

Install the visor shaft into the visor holder.


Hide 74320 8.INSTALL VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62471A 9.INSTALL ROOF SIDE INNER GARNISH RH

a.

Pass the rear seat 3 point type outer belt through the slit in the roof side inner garnish.


b.

Engage the 4 clips and install the roof side inner garnish.


Hide 62472A 10.INSTALL ROOF SIDE INNER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 64730B 11.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

a.

Engage the 3 clips.


b.

Engage the guide and the 4 claws and install the deck trim side panel.


c.

Install the 3 screws.


Hide 64740C 12.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 73360 13.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

a.

Engage the 2 claws and install the rear seat 3 point type outer belt.


b.

Tighten the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73370 14.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 58387B 15.INSTALL REAR FLOOR FINISH PLATE

a.

Engage the 4 guides and the 4 claws to install the rear floor finish plate.


Hide 09113 16.INSTALL JACK HANDLE

Hide 81250 17.INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 62211 18.INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

a.

Remove the piece of cloth or nylon.


b.

for 6 speakers:

i.

Connect the connector.



c.
B284321E01
2.046,0.743 2.207,0.885 0.161,0.142 10 *1 2.224,0.761 2.386,0.607 false

Make sure that the front pillar garnish clip is not damaged.

Text in Illustration
*1 Protective Tape

NOTICE:
·

If there is any damage, replace the garnish clip with a new one.

·

When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.




d.

Engage the 2 guides.


e.

Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish.

HINT:

Tape the needle-nosed pliers tip before use.



f.
B284391E01
0.992,0.826 1.156,0.980 0.164,0.154 10 *1 1.048,0.82 0.889,0.517 false

Engage the clip and the front pillar garnish clip to install the front pillar garnish.

Text in Illustration
*1 Front Pillar Garnish Clip


Hide 62212 19.INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure as for the RH side.


Hide 62211 20.INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

a.

for 6 speakers:

i.

Connect the connector.



b.

Engage the 2 guides and the 2 clips and install the front pillar garnish.


Hide 62212 21.INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure as for the RH side.


Hide 62411B 22.INSTALL CENTER PILLAR UPPER GARNISH RH

a.

Pass the front seat outer belt through the slit in the center pillar upper garnish.


b.

Engage the clip and install the center pillar upper garnish with 2 screws.


Hide 62412B 23.INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62413A 24.INSTALL CENTER PILLAR LOWER GARNISH RH

a.

Engage the 2 clips and the 2 claws.


b.

Engage the 2 guides and install the center pillar lower garnish.


Hide 62414A 25.INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 73210 26.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

a.

Install the floor end of the front seat outer belt with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Engage the 2 claws and install the anchor cover.


Hide 73220 27.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62331A 28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B284353E03
1.115,0.833 1.385,0.708 false 2.469,0.906 2.448,1.177 false 1.396,0.573 1.563,0.74 0.167,0.167 10 false *a 2.344,1.177 2.51,1.344 0.167,0.167 10 false *b

Align the paint mark on the rear door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.

Text in Illustration
*a Paint Mark
*b Flange Position

Paint Mark:
Area Color
RH Side Purple
LH Side Pink


NOTICE:

After installation, check that the corners fit correctly.



Hide 62332A 29.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 67917A 30.INSTALL REAR DOOR SCUFF PLATE RH

a.

Engage the guide and the 5 claws and install the rear door scuff plate.


Hide 67918A 31.INSTALL REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 62311B 32.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B284354E02
1.156,0.833 1.458,0.677 false 2.542,0.917 2.521,1.156 false 1.479,0.542 1.646,0.698 0.167,0.156 10 false *a 2.417,1.167 2.594,1.313 0.177,0.146 10 false *b

Align the paint mark on the front door opening trim weatherstrip with the flange position on the vehicle body and install the weatherstrip.

Text in Illustration
*a Paint Mark
*b Flange Position

Paint Mark:
Area Color
RH Side Gold
LH Side Silver


NOTICE:

After installation, check that the corners fit correctly.



Hide 62312B 33.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 62111C 34.INSTALL COWL SIDE TRIM BOARD RH

a.

Engage the clip.


b.

Install the cowl side trim board with clip.


Hide 62112 35.INSTALL COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure as for the RH side.


Hide 67913 36.INSTALL FRONT DOOR SCUFF PLATE RH

a.

Engage the 8 claws and install the front door scuff plate.


Hide 67914 37.INSTALL FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 38.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

Hide 39.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

Hide 40.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 64771G 41.INSTALL SPARE WHEEL COVER

a.

Install the spare wheel cover.


Hide 58410B 42.INSTALL DECK BOARD ASSEMBLY

a.

Install the deck board.