Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up and down function can be performed but the auto up and down function cannot, then the fail-safe mode may be functioning.

If the power window initialization has not been performed, the auto up and down function will not operate (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

WIRING DIAGRAM

B291671E01
0.073,0.084 0.729,0.268 0.656,0.184 12 for LHD: 0.958,2.501 2.561,2.822 1.603,0.321 10 Power Window Regulator Master Switch Assembly 1.721,1.197 2.127,1.343 0.406,0.145 10 AUTO 1.798,1.82 2.127,1.962 0.330,0.142 10 GND 0.958,2.342 1.162,2.485 0.204,0.143 10 H1 2.216,1.104 2.739,1.250 0.524,0.146 10 4*1, 1*2 2.691,3.027 4.361,3.173 1.670,0.145 10 *1: w/ Rear Power Window 2.691,3.29 4.444,3.436 1.753,0.145 10 *2: w/o Rear Power Window 4.866,1.104 4.963,1.250 0.097,0.145 10 4 5.069,1.201 5.482,1.339 0.413,0.139 10 AUTO 4.642,2.355 4.840,2.504 0.198,0.149 10 H3 4.642,2.526 6.253,3.037 1.611,0.510 10 Power Window Regulator Motor Assembly LH (Driver Side) 2.216,1.733 2.739,1.879 0.524,0.146 10 1*1, 7*2

B291671E02
0.066,0.084 0.759,0.268 0.693,0.184 12 for RHD: 0.951,2.501 2.554,2.822 1.603,0.321 10 Power Window Regulator Master Switch Assembly 1.714,1.197 2.120,1.343 0.406,0.145 10 AUTO 1.791,1.82 2.120,1.962 0.330,0.142 10 GND 2.218,1.104 2.820,1.250 0.602,0.146 10 4*1, 18*2 2.712,2.985 4.382,3.131 1.670,0.145 10 *1: w/ Rear Power Window 2.712,3.248 4.465,3.394 1.753,0.145 10 *2: w/o Rear Power Window 4.859,1.104 4.956,1.250 0.097,0.145 10 4 5.062,1.201 5.475,1.339 0.413,0.139 10 AUTO 4.635,2.355 4.851,2.504 0.216,0.149 10 G3 4.635,2.526 6.246,3.037 1.611,0.510 10 Power Window Regulator Motor Assembly RH (Driver Side) 2.218,1.728 2.737,1.875 0.519,0.146 10 9*1, 7*2 0.951,2.336 1.165,2.482 0.213,0.146 10 G1

CAUTION / NOTICE / HINT

NOTICE:
·

When the power window regulator motor assembly LH or RH (driver side) is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operations at least 5 times:

(a)

Close the power window by fully pulling up the power window regulator master switch assembly and holding it in the auto up position.

(b)

Open the power window by fully pushing down the power window regulator master switch assembly.




PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / D-Door Motor / Data List.


e.

According to the display on the intelligent tester, perform the Data List.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto switch signal /
OFF or ON
OFF: Driver side door power window auto switch not operated
ON: Driver side door power window auto switch operated
-

OK:

Normal conditions listed above are displayed.




OK

2.PERFORM INITIALIZATION

NG

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
2.PERFORM INITIALIZATION
a.

Initialize the power window regulator motor assembly LH or RH (driver side) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)
a.

Check that the driver side door power window moves when the auto up and down function of the power window regulator master switch assembly is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Driver side auto up and down function is normal.




OK

END

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH

4.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Inspect the power window regulator master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR LH OR RH)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR LH OR RH)
a.

for LHD

i.

Disconnect the H1 power window regulator master switch assembly connector.


ii.

Disconnect the H3 power window regulator motor assembly LH (driver side) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
H1-4 (AUTO) - H3-4 (AUTO) Always Below 1 Ω
H1-1 (GND) - Body ground Always Below 1 Ω
H1-4 (AUTO) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
H1-1 (AUTO) - H3-4 (AUTO) Always Below 1 Ω
H1-7 (GND) - Body ground Always Below 1 Ω
H1-1 (AUTO) - Body ground Always 10 kΩ or higher




b.

for RHD

i.

Disconnect the G1 power window regulator master switch assembly connector.


ii.

Disconnect the G3 power window regulator motor assembly RH (driver side) connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear Power Window
Tester Connection Condition Specified Condition
G1-4 (AUTO) - G3-4 (AUTO) Always Below 1 Ω
G1-9 (GND) - Body ground Always Below 1 Ω
G1-4 (AUTO) - Body ground Always 10 kΩ or higher

w/o Rear Power Window
Tester Connection Condition Specified Condition
G1-18 (AUTO) - G3-4 (AUTO) Always Below 1 Ω
G1-7 (GND) - Body ground Always Below 1 Ω
G1-18 (AUTO) - Body ground Always 10 kΩ or higher





OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH OR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR