Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051501 WINDOW / GLASS _0248389 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Key-off Operation Function Operates even if Operating Conditions are not Satisfied  


DESCRIPTION

When the front doors are closed, driver door power window regulator motor can control its power window operation for approximately 45 seconds after the ignition switch is turned from ON to off (the key is removed) by receiving operation permission signals from the main body ECU. However, when approximately 45 seconds have elapsed, or the driver door or front passenger door is opened within approximately 45 seconds of the ignition switch being turned off (the key is removed), the power window regulator motor stops operating.

During AUTO function operation, the window operation will continue until complete even if 45 seconds have passed or a door is opened.


WIRING DIAGRAM

B291672E01
0.051,2.02 2.127,2.332 2.076,0.312 10 Power Window Regulator Motor Assembly LH or RH (Driver Side) 0.594,3.166 0.785,3.311 0.191,0.145 10 K1 0.594,3.33 2.219,3.649 1.625,0.319 10 Front Door Courtesy Light Switch Assembly LH 2.909,3.355 3.989,3.854 1.079,0.500 10 Instrument Panel Junction Block Assembly 2.66,2.889 2.862,3.035 0.202,0.145 10 3D 2.675,2.7 2.848,2.845 0.173,0.145 10 36 3.823,2.887 4.052,3.037 0.229,0.150 10 MB 3.891,2.693 3.986,2.852 0.095,0.159 10 2 4.142,2.886 4.534,3.038 0.392,0.152 10 FLCY 4.034,3.922 5.054,4.071 1.020,0.149 10 Main Body ECU 4.991,2.104 5.264,2.250 0.272,0.145 10 F76 5.041,1.926 5.215,2.075 0.173,0.149 10 19 4.5,2.106 4.906,2.248 0.406,0.142 10 FRCY 5.211,2.388 5.408,2.540 0.198,0.152 10 K2 5.211,2.556 6.832,2.882 1.621,0.326 10 Front Door Courtesy Light Switch Assembly RH 0.832,4.213 2.450,4.362 1.618,0.149 10 : LIN Communication Line 1.737,2.803 1.832,2.963 0.095,0.159 10 1 5.609,2.019 5.704,2.178 0.095,0.159 10 1

CAUTION / NOTICE / HINT

NOTICE:

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.


PROCEDURE

1.CHECK OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF
a.

Check the power window operation function after the ignition switch is turned off.

Result
Result Proceed to
When power window can still be operated even after opening driver door or front passenger door within approximately 45 seconds of ignition switch being turned off A
When power window can still be operated even after approximately 45 seconds have elapsed after ignition switch turned off B



A

2.READ VALUE USING INTELLIGENT TESTER

B

2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH signal /
ON or OFF
ON: Front door RH closed
OFF: Front door RH opened
-
FL Door Courtesy Front door courtesy light switch LH signal /
ON or OFF
ON: Front door LH closed
OFF: Front door LH opened
-

OK:

Normal conditions listed above are displayed.




OK

NG