Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.

DTC No. DTC Detection Condition Trouble Area
B1244
·

Malfunction in automatic light control sensor.

·

Open or short in automatic light control sensor circuit.


·

Automatic light control sensor

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

E219666E01
1.765,1.009 2.140,1.161 0.375,0.152 10 CLTB 1.765,1.473 2.140,1.627 0.375,0.154 10 CLTS 1.763,1.934 2.140,2.086 0.377,0.152 10 CLTE 2.211,0.944 2.312,1.090 0.100,0.145 10 3 2.211,1.397 2.309,1.553 0.098,0.156 10 4 2.211,1.85 2.315,1.999 0.104,0.149 10 5 4.814,0.941 4.991,1.093 0.176,0.152 10 20 4.816,1.399 4.991,1.551 0.175,0.152 10 21 4.81,1.851 4.991,1.997 0.181,0.145 10 22 5.063,1.009 5.438,1.161 0.375,0.152 10 CLTB 5.063,1.473 5.438,1.627 0.375,0.154 10 CLTS 5.063,1.934 5.440,2.086 0.377,0.152 10 CLTE 1.252,2.393 1.514,2.535 0.262,0.142 10 F73 4.922,2.388 5.192,2.540 0.269,0.151 10 F76 4.922,2.561 5.953,2.726 1.031,0.165 10 Main Body ECU 1.252,2.575 2.245,2.907 0.994,0.332 10 Automatic Light Control Sensor

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1244 is not output.




OK

NG

2.READ VALUE USING INTELLIGENT TESTER
2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information/
0 to 2162.65 ms
Value output according to ambient light levels -

OK:

Normal conditions listed above are displayed.




OK

NG

3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
3.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - MAIN BODY ECU)
a.

Disconnect the F73 automatic light control sensor connector.


b.

Disconnect the F76 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-3 (CLTB) - F76-20 (CLTB) Always Below 1 Ω
F73-4 (CLTS) - F76-21 (CLTS) Always Below 1 Ω
F73-5 (CLTE) - F76-22 (CLTE) Always Below 1 Ω
F73-3 (CLTB) - Body ground Always 10 kΩ or higher
F73-4 (CLTS) - Body ground Always 10 kΩ or higher
F73-5 (CLTE) - Body ground Always 10 kΩ or higher




OK

4.CHECK MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MAIN BODY ECU
U158604E02
2.031,1.063 1.26,1.802 true 2.385,1.063 2.896,1.594 true 0.844,1.75 1.219,1.896 0.375,0.146 10 false CLTE 2.698,1.646 3.073,1.792 0.375,0.146 10 false CLTB 0.198,0.625 0.458,0.802 0.26,0.177 10 false F76 0.083,0.063 0.25,0.219 0.167,0.156 10 false *a

a.

Reconnect the main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F76-20 (CLTB) - F76-22 (CLTE) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Component with harness connected
(Main Body ECU)



OK

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR

NG

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR
a.
U158605E01
2.628,1.372 3.006,1.520 0.378,0.149 10 CLTS 0.557,1.569 0.935,1.715 0.378,0.145 10 CLTE 0.575,0.874 0.832,1.055 0.256,0.181 10 F73 0.089,0.088 0.258,0.248 0.170,0.161 10 *a 2.944,3.307 3.277,3.456 0.333,0.149 10 GND 1.849,3.66 1.967,3.809 0.118,0.149 10 A 1.698,1.142 2.589,1.457 false 1.511,1.298 1.038,1.651 false

Reconnect the automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.


c.

Check the waveform.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
F73-4 (CLTS) - F73-5 (CLTE) 5 V/DIV., 5 ms./DIV. Ignition switch ON, headlight dimmer switch in AUTO position Correct waveform is as shown


HINT:

When the ambient light becomes brighter, width A becomes narrower.


Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)



OK

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR