Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Relay Circuit  


DESCRIPTION

The main body ECU controls the headlight relay and headlight dimmer relay.

WIRING DIAGRAM

E219689E01
0.217,1.148 0.998,1.310 0.781,0.163 10 from Battery 1.905,1.295 2.627,1.444 0.722,0.149 10 H-LP MAIN 2.827,1.088 2.925,1.234 0.098,0.147 10 1 4.68,0.981 4.862,1.130 0.181,0.149 10 18 4.672,1.163 4.870,1.309 0.199,0.145 10 3C 5.94,1.16 6.329,1.312 0.389,0.152 10 HRLY 5.947,2.525 6.225,2.674 0.277,0.149 10 DIM 4.173,3.17 5.812,3.506 1.640,0.336 10 Instrument Panel Junction Block Assembly 5.765,3.854 6.778,4.024 1.012,0.170 10 Main Body ECU 5.557,1.162 5.786,1.310 0.229,0.147 10 MB 2.776,1.883 3.675,2.032 0.899,0.149 10 H-LP/US-DRL 3.29,3.324 3.573,3.471 0.283,0.147 10 DIM 2.046,3.677 2.829,3.828 0.783,0.151 10 H-LP LH LO 0.616,3.634 1.447,3.980 0.831,0.346 10 to Low Beam Headlight 1.359,4.608 2.231,4.938 0.872,0.330 10 to High Beam Headlight 2.036,4.078 2.838,4.229 0.802,0.151 10 H-LP RH LO 2.881,4.629 3.623,4.780 0.742,0.151 10 H-LP LH HI 2.872,5.031 3.632,5.182 0.760,0.151 10 H-LP RH HI 2.827,1.499 2.925,1.646 0.098,0.147 10 5 3.554,1.088 3.652,1.234 0.098,0.147 10 2 3.554,1.499 3.652,1.646 0.098,0.147 10 3 3.559,2.456 3.657,2.602 0.098,0.147 10 1 3.559,2.867 3.657,3.014 0.098,0.147 10 5 2.817,2.456 2.915,2.602 0.098,0.147 10 2 2.817,2.867 2.915,3.014 0.098,0.147 10 3 4.672,2.526 4.870,2.672 0.199,0.145 10 3C 5.557,2.526 5.786,2.673 0.229,0.147 10 MB 5.581,0.981 5.763,1.130 0.181,0.149 10 15 4.68,2.347 4.862,2.496 0.181,0.149 10 35 5.581,2.347 5.763,2.496 0.181,0.149 10 22 3.138,3.324 3.236,3.471 0.098,0.147 10 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Headlight relay OFF or ON -
Head Light Hi Headlight dimmer relay OFF or ON Light control switch is in HEAD position


f.

Check the illuminating condition of the low beam and high beam headlights.

Result
Result Proceed to
Low beam headlights and high beam headlights are normal. A
Low beam headlights and high beam headlights do not illuminate. B
Low beam headlights do not illuminate (High beam headlights are normal). C
High beam headlights do not illuminate (Low beam headlights are normal). D



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT HEADLIGHT RELAY (H-LP/US-DRL RELAY)

C

8.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)

D

9.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)
2.INSPECT HEADLIGHT RELAY (H-LP/US-DRL RELAY)
a.

Inspect the headlight relay (H-LP/US-DRL relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

3.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)

NG

REPLACE HEADLIGHT RELAY (H-LP/US-DRL RELAY)

3.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)
a.

Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BATTERY)

NG

REPLACE HEADLIGHT DIMMER RELAY (DIM RELAY)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - BATTERY)
a.
E222624E01
0.103,0.045 0.273,0.205 0.170,0.161 10 *1 2.838,2.503 3.008,2.663 0.170,0.161 10 *2

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H-LP/US-DRL-1 - Body ground Always 11 to 14 V
H-LP/US-DRL-5 - Body ground Always 11 to 14 V


Text in Illustration
*1 No. 2 Engine Room Relay Block
*2 Headlight Rely (H-LP/US-DRL Relay) Holder



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT DIMMER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT DIMMER RELAY)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-LP/US-DRL-3 - DIM-2 Always Below 1 Ω
H-LP/US-DRL-3 - DIM-3 Always Below 1 Ω
H-LP/US-DRL-3 - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT RELAY AND HEADLIGHT DIMMER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT RELAY AND HEADLIGHT DIMMER RELAY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


c.

Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - H-LP/US-DRL-2 Always Below 1 Ω
3C-35 - DIM-1 Always Below 1 Ω
3C-18 - Body ground Always 10 kΩ or higher
3C-35 - Body ground Always 10 kΩ or higher




OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Remove the main body ECU from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U158606E01
0.071,0.094 0.240,0.255 0.170,0.161 10 *a 1.684,0.226 1.878,0.407 0.195,0.181 10 3C 4.958,0.481 5.183,0.662 0.225,0.181 10 MB 4.635,1.252 5.034,1.408 0.399,0.156 10 HRLY 5.639,1.252 5.916,1.408 0.277,0.156 10 DIM 4.94,0.98 4.828,1.232 false 5.67,0.98 5.768,1.237 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3C-18 - MB-15 (HRLY) Always Below 1 Ω
3C-35 - MB-22 (DIM) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)
a.

Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE HEADLIGHT DIMMER RELAY (DIM RELAY)

9.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)
a.

Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT DIMMER RELAY)

NG

REPLACE HEADLIGHT DIMMER RELAY (DIM RELAY)

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY - HEADLIGHT DIMMER RELAY)
a.

Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.


b.

Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-LP/US-DRL-3 - DIM-2 Always Below 1 Ω
H-LP/US-DRL-3 - Body ground Always 10 kΩ or higher




OK

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DIM-1 - 3C-35 Always Below 1 Ω
DIM-1 - Body ground Always 10 kΩ or higher




OK

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Remove the main body ECU from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U158607E01
0.071,0.094 0.240,0.255 0.170,0.161 10 *a 1.684,0.226 1.878,0.407 0.195,0.181 10 3C 4.958,0.481 5.183,0.662 0.225,0.181 10 MB 5.639,1.252 5.916,1.408 0.277,0.156 10 DIM 5.67,0.98 5.768,1.237 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3C-35 - MB-22 (DIM) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY