The main body ECU controls the headlight relay and headlight dimmer relay.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight Relay | Headlight relay | OFF or ON | - |
| Head Light Hi | Headlight dimmer relay | OFF or ON | Light control switch is in HEAD position |
Check the illuminating condition of the low beam and high beam headlights.
| Result | Proceed to |
|---|---|
| Low beam headlights and high beam headlights are normal. | A |
| Low beam headlights and high beam headlights do not illuminate. | B |
| Low beam headlights do not illuminate (High beam headlights are normal). | C |
| High beam headlights do not illuminate (Low beam headlights are normal). | D |
A
B
C
D
Remove the headlight relay (H-LP/US-DRL relay).
Inspect the headlight relay (H-LP/US-DRL relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the headlight dimmer relay (DIM relay).
Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H-LP/US-DRL-1 - Body ground | Always | 11 to 14 V |
| H-LP/US-DRL-3 - Body ground | Always | 11 to 14 V |
| *1 | No. 2 Engine Room Relay Block |
| *2 | Headlight Rely (H-LP/US-DRL Relay) Holder |
OK
NG
Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.
Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H-LP/US-DRL-5 - DIM-2 | Always | Below 1 Ω |
| H-LP/US-DRL-5 - DIM-3 | Always | Below 1 Ω |
| H-LP/US-DRL-5 or DIM-2 - Body ground | Always | 10 kΩ or higher |
| H-LP/US-DRL-5 or DIM-3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.
Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-18 - H-LP/US-DRL-2 | Always | Below 1 Ω |
| 3C-35 - DIM-1 | Always | Below 1 Ω |
| 3C-18 or H-LP/US-DRL-2 - Body ground | Always | 10 kΩ or higher |
| 3C-35 or DIM-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly.
Remove the main body ECU from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-18 - MB-15 (HRLY) | Always | Below 1 Ω |
| 3C-35 - MB-22 (DIM) | Always | Below 1 Ω |
OK
NG
Remove the headlight dimmer relay (DIM relay).
Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the headlight dimmer relay (DIM relay).
Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the headlight relay (H-LP/US-DRL relay) from the No. 2 engine room relay block.
Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H-LP/US-DRL-5 - DIM-2 | Always | Below 1 Ω |
| H-LP/US-DRL-5 or DIM-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.
Disconnect the 3C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DIM-1 - 3C-35 | Always | Below 1 Ω |
| DIM-1 or 3C-35 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly.
Remove the main body ECU from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-35 - MB-22 (DIM) | Always | Below 1 Ω |
OK
NG