Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.07–2017.10
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives information signals from the hazard warning signal switch assembly.

WIRING DIAGRAM

E231512E01
1.348,0.748 2.131,0.920 0.783,0.172 10 from Battery 5.222,2.202 7.061,2.355 1.839,0.153 10 Combination Meter Assembly 3.776,1.423 3.883,1.577 0.107,0.155 10 4 2.739,1.421 2.837,1.579 0.098,0.158 10 1 2.584,1.93 4.036,2.256 1.452,0.325 10 Hazard Warning Signal Switch Assembly 5.712,0.663 5.812,0.835 0.100,0.173 10 1 5.702,1.408 5.812,1.581 0.110,0.173 10 3 5.222,2.045 5.407,2.201 0.185,0.155 10 F3 2.584,1.774 2.783,1.946 0.199,0.173 10 F2 3.119,0.892 3.420,1.043 0.301,0.151 10 HAZ 5.9,0.754 6.014,0.903 0.114,0.149 10 B 5.895,1.51 6.199,1.650 0.304,0.140 10 HAZ

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard warning signal switch /
OFF or ON
OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.

Inspect the hazard warning signal switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY)
U158609E01
0.079,0.044 0.249,0.205 0.170,0.161 10 *a 0.536,1.62 0.671,1.781 0.135,0.161 10 B 0.289,0.933 0.468,1.114 0.179,0.181 10 F3 1.067,1.184 0.682,1.708 false

a.

Disconnect the F3 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F3-1 (B) - Body Ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F2 hazard warning signal switch assembly connector.


b.

Disconnect the F3 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F2-4 - F3-3 (HAZ) Always Below 1 Ω
F2-1 - Body Ground Always Below 1 Ω
F2-4 - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR