Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Dimmer Switch Circuit  


DESCRIPTION

The main body ECU receives the following signals:

·

Headlight dimmer switch TAIL, HEAD, AUTO, HIGH or high flash signal

·

Fog light switch signal*1

*1: w/ Fog Light



The combination meter assembly receives the following signals:

·

Turn signal switch turn right or turn left signal


WIRING DIAGRAM

E231511E01
0.154,1.642 0.678,1.795 0.524,0.154 10 3*2, 8*3 0.703,1.645 1.032,1.792 0.329,0.147 10 LFG 0.005,5.18 0.691,5.352 0.686,0.171 10 12*2, 19*3 0.703,5.187 0.915,5.346 0.212,0.159 10 EL 2.561,4.84 2.981,4.984 0.420,0.144 10 AUTO 2.566,4.599 2.976,4.748 0.410,0.149 10 HEAD 2.616,4.366 2.927,4.512 0.311,0.146 10 TAIL 2.621,4.123 2.922,4.270 0.301,0.148 10 OFF 4.134,3.888 4.343,4.046 0.209,0.157 10 A 3.813,3.888 4.040,4.046 0.227,0.157 10 H 3.495,3.888 3.711,4.046 0.216,0.157 10 T 3.138,3.888 3.331,4.046 0.193,0.157 10 EL 2.52,1.168 3.022,1.325 0.502,0.157 10 FRONT 2.623,0.924 2.920,1.082 0.297,0.157 10 OFF 3.391,0.69 3.709,0.847 0.317,0.157 10 BFG 3.088,0.69 3.395,0.847 0.308,0.157 10 LFG 2.581,2.835 2.962,2.992 0.381,0.157 10 HIGH 2.599,2.602 2.944,2.760 0.345,0.157 10 LOW 2.536,2.359 3.006,2.516 0.470,0.157 10 FLASH 4.078,2.139 4.318,2.296 0.241,0.157 10 HF 3.758,2.139 4.006,2.296 0.248,0.157 10 HU 3.439,2.139 3.683,2.296 0.244,0.157 10 HL 3.136,2.139 3.371,2.296 0.235,0.157 10 ED 5.948,0.221 6.163,0.378 0.215,0.157 10 27 6.016,4.248 6.283,4.427 0.267,0.179 10 F76 1.57,6.972 1.846,7.152 0.276,0.179 10 F9 5.948,3.805 6.176,3.963 0.228,0.157 10 28 5.948,3.423 6.164,3.580 0.216,0.157 10 29 6.018,1.639 6.116,1.796 0.098,0.157 10 5 6.018,2.03 6.116,2.187 0.098,0.157 10 8 5.948,3.024 6.170,3.181 0.222,0.157 10 30 4.448,1.639 4.684,1.796 0.236,0.157 10 HU 4.56,3.805 4.685,3.963 0.125,0.157 10 A 4.555,3.423 4.685,3.580 0.129,0.157 10 H 4.592,3.024 4.699,3.181 0.106,0.157 10 T 4.38,0.217 4.683,0.374 0.303,0.157 10 BFG 4.462,2.03 4.684,2.187 0.222,0.157 10 HF 6.202,1.724 6.480,1.882 0.279,0.157 10 HU 6.202,2.117 6.486,2.274 0.284,0.157 10 HF 6.202,3.892 6.551,4.036 0.350,0.144 10 A 6.202,0.311 6.675,0.521 0.474,0.210 10 FFOG 6.202,3.506 6.660,3.688 0.458,0.182 10 HEAD 6.202,3.112 6.632,3.259 0.430,0.146 10 TAIL 1.282,2.444 2.235,2.598 0.954,0.154 10 Dimmer Switch 1.124,4.352 2.390,4.510 1.265,0.158 10 Light Control Switch 1.228,0.916 2.288,1.078 1.061,0.162 10 Fog Light Switch 1.57,7.136 3.802,7.319 2.232,0.183 10 Headlight Dimmer Switch Assembly 6.016,4.412 7.021,4.567 1.005,0.155 10 Main Body ECU 4.774,1.639 5.447,1.796 0.674,0.157 10 11*2, 20*3 4.774,3.805 5.441,3.963 0.667,0.157 10 19*2, 12*3 5.636,0.223 5.790,0.376 0.153,0.153 10 *1 4.774,3.423 5.446,3.580 0.673,0.157 10 20*2, 11*3 4.774,3.024 5.449,3.181 0.675,0.157 10 18*2, 13*3 4.774,2.03 5.456,2.187 0.683,0.157 10 17*2, 14*3 4.774,0.221 5.287,0.378 0.513,0.157 10 4*2, 7*3 2.712,6.203 2.833,6.360 0.122,0.157 10 N 2.663,5.962 2.882,6.119 0.219,0.157 10 RH 2.672,6.422 2.872,6.580 0.200,0.157 10 LH 3.767,5.725 4.052,5.882 0.285,0.157 10 TL 3.455,5.725 3.773,5.882 0.317,0.157 10 TR 3.132,5.725 3.337,5.882 0.206,0.157 10 EL 6.008,5.249 6.111,5.406 0.104,0.157 10 9 5.904,5.882 6.102,6.061 0.198,0.179 10 F3 5.925,5.627 6.124,5.795 0.199,0.167 10 10 4.774,5.627 5.443,5.798 0.669,0.171 10 15*2, 18*3 4.471,5.237 4.684,5.394 0.212,0.157 10 TR 4.492,5.619 4.684,5.776 0.192,0.157 10 TL 6.202,5.716 6.409,5.870 0.208,0.154 10 EL 6.202,5.331 6.432,5.541 0.231,0.210 10 ER 1.162,6.054 2.353,6.213 1.191,0.159 10 Turn Signal Switch 5.904,6.046 7.117,6.648 1.213,0.602 10 Combination Meter Assembly 4.913,7.108 5.700,7.273 0.787,0.165 10 *2: for LHD 4.913,6.811 6.284,6.965 1.371,0.154 10 *1: w/ Fog Light 4.774,5.249 5.457,5.406 0.683,0.157 10 13*2, 16*3 4.932,7.416 5.715,7.570 0.783,0.154 10 *3: for RHD

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

i.

for Main Body ECU: Body / Main Body / Data List.


ii.

for Combination Meter: Body / Combination Meter / Data List.



e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Dimmer SW Dimmer switch high signal /
OFF or ON
OFF: Dimmer switch in low position
ON: Dimmer switch in high or high flash position
-
Passing Light SW Dimmer switch high flash signal /
OFF or ON
OFF: Dimmer switch not in high flash position
ON: Dimmer switch in high flash position
-
Front Fog Light SW*1 Fog light switch signal /
OFF or ON
OFF: Fog light switch off
ON: Fog light switch on
-
Auto Light SW Light control switch AUTO signal /
OFF or ON
OFF: Light control switch not in AUTO position
ON: Light control switch in AUTO position
-
Head Light SW (Head) Light control switch HEAD signal /
OFF or ON
OFF: Light control switch not in HEAD position
ON: Light control switch in HEAD position
-
Head Light SW (Tail) Light control switch TAIL signal /
OFF or ON
OFF: Light control switch not in TAIL and HEAD position
ON: Light control switch in TAIL or HEAD position
-

*1: w/ Fog Light


Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Turn Signal Switch (Right) Turn signal switch signal (turn right) /
OFF or ON
OFF: Turn signal switch right off (turn right)
ON: Turn signal switch right on (turn right)
-
Turn Signal Switch (Left) Turn signal switch signal (turn left) /
OFF or ON
OFF: Turn signal switch left off (turn left)
ON: Turn signal switch left on (turn left)
-

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
OK A
NG (Light control switch, dimmer switch or fog light switch*1) B
NG (Turn signal switch) C

*1: w/ Fog Light




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (LIGHT CONTROL SWITCH, DIMMER SWITCH OR FOG LIGHT SWITCH)

C

4.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL SWITCH)
2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (LIGHT CONTROL SWITCH, DIMMER SWITCH OR FOG LIGHT SWITCH)
a.

Inspect the headlight dimmer switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the F9 headlight dimmer switch assembly connector.


b.

Disconnect the F76 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F9-4 (BFG) - F76-27 (FFOG)*1 Always Below 1 Ω
F9-11 (HU) - F76-5 (HU) Always Below 1 Ω
F9-17 (HF) - F76-8 (HF) Always Below 1 Ω
F9-18 (T) - F76-30 (TAIL) Always Below 1 Ω
F9-19 (A) - F76-28 (A) Always Below 1 Ω
F9-20 (H) - F76-29 (HEAD) Always Below 1 Ω
F9-3 (LFG) - Body ground Always Below 1 Ω
F9-12 (EL) - Body ground Always Below 1 Ω
F9-4 (BFG) - Body ground*1 Always 10 kΩ or higher
F9-11 (HU) - Body ground Always 10 kΩ or higher
F9-17 (HF) - Body ground Always 10 kΩ or higher
F9-18 (T) - Body ground Always 10 kΩ or higher
F9-19 (A) - Body ground Always 10 kΩ or higher
F9-20 (H) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F9-7 (BFG) - F76-27 (FFOG)*1 Always Below 1 Ω
F9-20 (HU) - F76-5 (HU) Always Below 1 Ω
F9-14 (HF) - F76-8 (HF) Always Below 1 Ω
F9-13 (T) - F76-30 (TAIL) Always Below 1 Ω
F9-12 (A) - F76-28 (A) Always Below 1 Ω
F9-11 (H) - F76-29 (HEAD) Always Below 1 Ω
F9-8 (LFG) - Body ground Always Below 1 Ω
F9-19 (EL) - Body ground Always Below 1 Ω
F9-7 (BFG) - Body ground*1 Always 10 kΩ or higher
F9-20 (HU) - Body ground Always 10 kΩ or higher
F9-14 (HF) - Body ground Always 10 kΩ or higher
F9-13 (T) - Body ground Always 10 kΩ or higher
F9-12 (A) - Body ground Always 10 kΩ or higher
F9-11 (H) - Body ground Always 10 kΩ or higher


*1: w/ Fog Light




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (TURN SIGNAL SWITCH)
a.

Inspect the headlight dimmer switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F9 headlight dimmer switch assembly connector.


b.

Disconnect the F3 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F9-13 (TR) - F3-9 (ER) Always Below 1 Ω
F9-15 (TL) - F3-10 (EL) Always Below 1 Ω
F9-12 (EL) - Body ground Always Below 1 Ω
F9-13 (TR) - Body ground Always 10 kΩ or higher
F9-15 (TL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F9-16 (TR) - F3-9 (ER) Always Below 1 Ω
F9-18 (TL) - F3-10 (EL) Always Below 1 Ω
F9-19 (EL) - Body ground Always Below 1 Ω
F9-16 (TR) - Body ground Always 10 kΩ or higher
F9-18 (TL) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR