Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2011.08–2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU controls the TAIL relay.

WIRING DIAGRAM

E229433E01
4.357,1.951 4.668,2.106 0.311,0.155 10 TAIL 4.137,2.456 4.849,2.610 0.713,0.154 10 TAIL NO. 2 3.097,2.869 3.297,3.031 0.200,0.161 10 3D 3.095,2.306 3.300,2.452 0.205,0.146 10 3C 3.1,1.23 3.295,1.387 0.195,0.157 10 3F 5.902,1.231 6.276,1.382 0.374,0.151 10 TRLY 3.146,1.042 3.249,1.215 0.103,0.173 10 1 2.75,1.23 2.950,1.378 0.200,0.148 10 3E 2.797,1.042 2.905,1.215 0.108,0.173 10 1 3.114,1.422 3.281,1.594 0.166,0.173 10 *2 2.773,1.422 2.929,1.594 0.156,0.173 10 *1 5.577,1.052 5.762,1.205 0.185,0.153 10 14 5.553,1.223 5.786,1.373 0.233,0.150 10 MB 3.141,2.116 3.254,2.288 0.112,0.173 10 2 3.109,2.683 3.286,2.856 0.177,0.173 10 10 1.116,1.221 1.916,1.391 0.800,0.170 10 from Battery 3.834,3.412 5.469,3.748 1.636,0.336 10 Instrument Panel Junction Block Assembly 5.776,3.875 6.782,4.044 1.006,0.169 10 Main Body ECU 0.655,2.308 1.883,2.466 1.229,0.158 10 to Clearance Lights 2.332,3.828 3.045,3.993 0.713,0.165 10 *1: for LHD 2.332,4.14 3.063,4.303 0.731,0.164 10 *2: for RHD 1.174,2.871 1.895,3.035 0.721,0.165 10 to Taillights 0.466,3.415 1.889,3.586 1.423,0.172 10 to License Plate Lights

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -

OK:

TAIL relay operates. (Clearance lights, taillights and license plate lights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
U158610E01
0.077,0.026 0.247,0.187 0.170,0.161 10 *a 0.745,1.025 0.914,1.185 0.170,0.161 10 *A 0.745,1.598 0.914,1.758 0.170,0.161 10 *B 0.734,0.769 0.921,0.950 0.187,0.181 10 3E 0.734,1.342 0.913,1.523 0.179,0.181 10 3F

a.

for LHD

i.

Disconnect the 3E instrument panel junction block assembly connectors.



b.

for RHD

i.

Disconnect the 3F instrument panel junction block assembly connectors.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

3.REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE MAIN BODY ECU
a.


NEXT

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -

OK:

TAIL relay operates. (Clearance lights, taillights and license plate lights illuminate.)




OK

END (MAIN BODY ECU WAS DEFECTIVE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY