Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  High Beam Headlight Circuit  


DESCRIPTION

The main body ECU controls the high beam headlights.

WIRING DIAGRAM

E249420E05
0.236,0.884 1.017,1.047 0.781,0.163 10 from Battery 1.352,1.023 2.074,1.172 0.722,0.149 10 H-LP MAIN 6.248,0.895 6.526,1.044 0.277,0.149 10 DIM 4.546,1.648 6.186,1.985 1.640,0.336 10 Instrument Panel Junction Block Assembly 6.118,2.484 7.131,2.654 1.012,0.170 10 Main Body ECU 0.56,2.556 2.176,2.739 1.615,0.184 10 to High Beam Headlights 2.821,2.498 3.563,2.650 0.742,0.151 10 H-LP LH HI 2.812,2.9 3.572,3.051 0.760,0.151 10 H-LP RH HI 5.197,0.897 5.396,1.043 0.199,0.145 10 3C 5.914,0.896 6.143,1.043 0.229,0.147 10 MB 5.206,0.717 5.388,0.866 0.181,0.149 10 35 5.938,0.717 6.120,0.866 0.181,0.149 10 22 3.496,0.804 3.594,0.951 0.098,0.147 10 1 2.761,0.804 2.859,0.951 0.098,0.147 10 2 2.761,1.23 2.859,1.377 0.098,0.147 10 3 3.496,1.23 3.594,1.377 0.098,0.147 10 5 3.036,1.609 3.340,1.760 0.304,0.151 10 DIM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEAD LIGHT HI)
a.

Connect the Intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Intelligent tester on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

According to the display on the Intelligent tester, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Hi Headlight dimmer relay OFF or ON -

OK:

Headlight dimmer relay operates (High beam headlight illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)
2.INSPECT HEADLIGHT DIMMER RELAY (DIM RELAY)
a.

Remove the headlight dimmer relay (DIM relay).


b.

Inspect the headlight dimmer relay (DIM relay) (See page Vehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - BATTERY)

NG

REPLACE HEADLIGHT DIMMER RELAY (DIM RELAY)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - BATTERY)
a.
E299194E01
0.084,0.062 0.258,0.217 0.173,0.156 10 *1 2.439,2.588 2.612,2.744 0.173,0.156 10 *2

Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DIM-2 - Body ground Always 11 to 14 V
DIM-3 - Body ground Always 11 to 14 V


Text in Illustration
*1 No. 2 Engine Room Relay Block
*2 Headlight Dimmer Relay (DIM Relay) Holder



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight dimmer relay (DIM relay) from the No. 2 engine room relay block.


b.

Disconnect the 3C instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DIM-1 - 3C-35 Always Below 1 Ω
DIM-2 or 3C-35 - Body ground Always 10 kΩ or higher




OK

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


b.

Remove the main body ECU from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U135134E01
0.085,0.094 0.254,0.255 0.170,0.161 10 *a 1.698,0.226 1.892,0.407 0.195,0.181 10 3C 4.972,0.481 5.197,0.662 0.225,0.181 10 MB 5.653,1.252 5.930,1.408 0.277,0.156 10 DIM 5.684,0.98 5.782,1.237 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3C-35 - MB-22 (DIM) Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY