Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248427 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Speed Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly receives the vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E298888E03
0.5,1.615 2.167,2 1.667,0.385 10 false Brake Actuator Assembly (Skid Control ECU) 1.969,0.76 2.177,0.938 0.208,0.177 10 false 11 1.615,0.771 1.906,0.917 0.292,0.146 10 false SP1 0.5,1.469 0.792,1.615 0.292,0.146 10 false A54 4.969,3.323 6.813,3.646 1.844,0.323 10 false Combination Meter Assembly 4.969,3.146 5.198,3.323 0.229,0.177 10 false F1 5.042,2.563 5.188,2.74 0.146,0.177 10 false 6 0.802,3.323 1.156,3.625 0.354,0.302 10 false ECM 5.042,0.75 5.188,0.927 0.146,0.177 10 false 5 0.813,3.167 1.083,3.313 0.271,0.146 10 false A74 1.708,2.573 1.917,2.75 0.208,0.177 10 false 8 4.208,2.667 4.406,2.813 0.198,0.146 10 false 3B 4.208,2.479 4.417,2.656 0.208,0.177 10 false 15 2.969,2.677 3.167,2.823 0.198,0.146 10 false 3C 2.979,2.479 3.188,2.656 0.208,0.177 10 false 39 4.208,5.083 4.406,5.229 0.198,0.146 10 false 3A 4.208,4.896 4.417,5.073 0.208,0.177 10 false 16 2.969,5.083 3.167,5.229 0.198,0.146 10 false 3C 2.979,4.896 3.188,5.073 0.208,0.177 10 false 40 5.25,2.563 5.479,2.74 0.229,0.177 10 false +S 5.271,0.76 5.469,0.938 0.198,0.177 10 false SI 1.302,2.677 1.635,2.854 0.333,0.177 10 false SPD 5.708,3.948 6.042,4.125 0.333,0.177 10 false SPD 5.708,5.083 6.042,5.26 0.333,0.177 10 false SPD 1.198,5.094 1.656,5.271 0.458,0.177 10 false SPDR 5.719,5.667 7,5.99 1.281,0.323 10 false Radio and Display Receiver Assembly 5.719,5.49 6.188,5.667 0.469,0.177 10 false F127 5.219,4.5 7.146,4.823 1.927,0.323 10 false Navigation Receiver Assembly 5.219,4.333 5.667,4.51 0.448,0.177 10 false F132 0.063,5.625 2.24,6.052 2.177,0.427 10 false Headlight Leveling ECU Assembly 0.063,5.458 0.344,5.635 0.281,0.177 10 false A82 5.417,3.854 5.646,4.031 0.229,0.177 10 false 17 5.417,4.99 5.646,5.167 0.229,0.177 10 false 17 5.042,3.854 5.25,4.031 0.208,0.177 10 false *2 5.073,4.99 5.281,5.167 0.208,0.177 10 false *3 2.219,4.99 2.427,5.167 0.208,0.177 10 false *1 1.708,4.99 2.042,5.167 0.333,0.177 10 false 16 2.917,5.656 4.563,6.25 1.646,0.594 10 false Instrument Panel Junction Block Assembly 0.125,6.188 1.719,6.51 1.594,0.323 10 false *1: w/ Headlight Leveling 0.125,6.51 2.531,6.833 2.406,0.323 10 false *2: for Navigation Receiver Type 2.625,6.198 4.906,6.521 2.281,0.323 10 false *3: for Radio and Display Type


PROCEDURE

1.CHECK COMBINATION METER SYSTEM
a.

The circuits that send vehicle speed signals to this system are inspected in the meter section (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit).


b.

During inspection for the meter system, if there is an instruction that indicates to go back to inspections for the lighting system, proceed to the next step.



NEXT

2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the A82 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-16 (SPDR) - F1-6 (+S) Always Below 1 Ω




OK

3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E219774E10
1.719,2.146 1.583,1.438 false 1.781,2.052 2.417,2.448 0.635,0.396 10 false F1-6 (+S) 3.01,3.531 3.354,3.927 0.344,0.396 10 false GND 0.073,0.24 0.417,0.635 0.344,0.396 10 false *a

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal F1-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is displayed as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE COMBINATION METER ASSEMBLY