Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.07–2016.09
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU, which uses this information to create the vehicle speed sensor signal*1. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2, which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.

·

*1: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.


HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.


WIRING DIAGRAM

E298888E04
0.5,1.594 2.167,1.979 1.667,0.385 10 false Brake Actuator Assembly (Skid Control ECU) 1.969,0.74 2.177,0.917 0.208,0.177 10 false 11 1.594,0.74 1.927,0.917 0.333,0.177 10 false SP1 0.5,1.438 0.823,1.625 0.323,0.188 10 false A54 4.969,3.25 6.813,3.573 1.844,0.323 10 false Combination Meter Assembly 4.969,3.104 5.198,3.281 0.229,0.177 10 false F1 5.042,2.542 5.188,2.719 0.146,0.177 10 false 6 0.802,3.365 1.156,3.667 0.354,0.302 10 false ECM 5.042,0.729 5.188,0.906 0.146,0.177 10 false 5 0.813,3.208 1.125,3.375 0.313,0.167 10 false A74 1.708,2.531 1.917,2.708 0.208,0.177 10 false 8 4.198,2.677 4.448,2.844 0.25,0.167 10 false 3B 4.208,2.458 4.417,2.635 0.208,0.177 10 false 15 2.958,2.677 3.229,2.865 0.271,0.188 10 false 3C 2.979,2.458 3.188,2.635 0.208,0.177 10 false 39 4.188,5.094 4.448,5.26 0.26,0.167 10 false 3A 4.208,4.896 4.417,5.073 0.208,0.177 10 false 16 2.969,5.094 3.24,5.26 0.271,0.167 10 false 3C 2.979,4.885 3.188,5.063 0.208,0.177 10 false 40 5.25,2.542 5.479,2.719 0.229,0.177 10 false +S 5.25,0.74 5.448,0.917 0.198,0.177 10 false SI 1.302,2.656 1.635,2.833 0.333,0.177 10 false SPD 5.667,3.948 6.073,4.135 0.406,0.188 10 false SPD 5.688,5.073 6.083,5.26 0.396,0.188 10 false SPD 1.198,5.073 1.656,5.25 0.458,0.177 10 false SPDR 5.698,5.635 6.979,6.01 1.281,0.375 10 false Radio and Display Receiver Assembly 5.719,5.469 6.188,5.646 0.469,0.177 10 false F127 5.219,4.427 7.146,4.75 1.927,0.323 10 false Navigation Receiver Assembly 5.219,4.271 5.667,4.448 0.448,0.177 10 false F132 0.063,5.583 2.229,5.813 2.167,0.229 10 false Headlight Leveling ECU Assembly 0.063,5.427 0.406,5.604 0.344,0.177 10 false A82 5.417,3.854 5.646,4.031 0.229,0.177 10 false 17 5.417,4.969 5.646,5.146 0.229,0.177 10 false 17 5.042,3.844 5.25,4.021 0.208,0.177 10 false *2 5.177,4.958 5.385,5.135 0.208,0.177 10 false *3 2.219,4.969 2.427,5.146 0.208,0.177 10 false *1 1.677,4.958 2.01,5.135 0.333,0.177 10 false 16 2.927,5.594 4.573,6.188 1.646,0.594 10 false Instrument Panel Junction Block Assembly 0.125,6.135 1.719,6.458 1.594,0.323 10 false *1: w/ Headlight Leveling 0.125,6.479 2.531,6.802 2.406,0.323 10 false *2: for Navigation Receiver Type 2.635,6.188 4.917,6.51 2.281,0.323 10 false *3: for Radio and Display Type

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (INPUT VOLTAGE)
a.
U127306E01
1.607,0.141 1.795,0.298 0.188,0.156 10 F1 1.121,1.068 0.974,1.644 false 0.873,1.673 1.086,1.829 0.213,0.156 10 +S 0.2,0.098 0.413,0.254 0.213,0.156 10 *a

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-6 (+S) - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



c.

Reconnect the combination meter assembly connector.



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
U158549E01
1.133,0.738 1.429,0.895 0.295,0.156 10 A54 0.095,0.067 0.391,0.223 0.295,0.156 10 *a 2.183,2.901 2.644,3.058 0.461,0.156 10 SP1 1.778,1.819 2.338,2.874 false

Disconnect the brake actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A54-11 (SP1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly)


c.

Reconnect the brake actuator assembly connector.



OK

3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E219774E11
1.667,1.427 1.99,2.031 false 1.833,2.052 2.479,2.271 0.646,0.219 10 false F1-5 (SI) 3.01,3.542 3.365,3.729 0.354,0.188 10 false GND 0.073,0.667 0.385,0.854 0.313,0.188 10 false *a

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F1-5 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Driving at approximately 20 km/h (12 mph)

OK:

The waveform is displayed as shown in the illustration.


HINT:

As the vehicle speed increases, the cycle of the waveform narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)




OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the A54 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-11 (SP1) - F1-5 (SI) Always Below 1 Ω
A54-11 (SP1) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-6 (+S) - 3B-15 Always Below 1 Ω
F1-6 (+S) - Body ground Always 10 kΩ or higher



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the combination meter assembly connector.



OK

6.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT HEADLIGHT LEVELING ECU ASSEMBLY
HINT:

For vehicle without headlight leveling, go to step 7.


a.
U158632E02
0.135,0.042 0.49,0.406 0.354,0.365 10 false *a 1.635,0.323 1.917,0.51 0.281,0.188 10 false 3C

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3C-40 - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

7.SYSTEM CHECK

NG

12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
7.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
for Radio and Display Receiver Type A
for Navigation Receiver Type B
w/o Audio C



A

8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

B

10.INSPECT NAVIGATION RECEIVER ASSEMBLY

C

11.INSPECT ECM
8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U158634E02
0.073,0.042 0.427,0.406 0.354,0.365 10 false *a 1.635,0.313 1.906,0.5 0.271,0.188 10 false 3A

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-16 - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

9.INSPECT ECM

NG

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
9.INSPECT ECM
a.
U158633E02
0.073,0.042 0.427,0.406 0.354,0.365 10 false *a 1.635,0.323 1.917,0.5 0.281,0.177 10 false 3C

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3C-39 - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
10.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
U158634E02
0.073,0.042 0.427,0.406 0.354,0.365 10 false *a 1.635,0.313 1.906,0.5 0.271,0.188 10 false 3A

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-16 - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)



OK

11.INSPECT ECM

NG

14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
11.INSPECT ECM
a.
U127339E02
0.073,0.042 0.427,0.406 0.354,0.365 10 false *a 1.646,0.313 1.844,0.469 0.198,0.156 10 false 3C

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3C-39 - Body ground Ignition switch ON 4.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


c.

Reconnect the instrument panel junction block assembly connector.



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
12.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Disconnect the A82 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-40 - A82-16 (SPDR) Always Below 1 Ω
3C-40 - Body ground Always 10 kΩ or higher



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the headlight leveling ECU assembly connector.



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Disconnect the F132 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-16 - F132-17 (SPD) Always Below 1 Ω
3A-16 - Body ground Always 10 kΩ or higher



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the radio and display receiver assembly connector.



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the 3A instrument panel junction block assembly connector.


b.

Disconnect the F127 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-16 - F127-17 (SPD) Always Below 1 Ω
3A-16 - Body ground Always 10 kΩ or higher



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the navigation receiver assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Disconnect the A74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-39 - A74-8 (SPD) Always Below 1 Ω
3C-39 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for 1NZ-FE) B
OK (for 2NZ-FE) C


d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the ECM connector.



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C