Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2014.07
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248427 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B2416  Height Control Sensor Malfunction  


DESCRIPTION

The DTC is stored when the headlight leveling ECU assembly detects malfunctions in the rear height control sensor sub-assembly power source or rear height control sensor sub-assembly.

DTC No. DTC Detecting Condition Trouble Area
B2416
·

Malfunction in rear height control sensor sub-assembly

·

Open or short in rear height control sensor sub-assembly power source circuit


·

Rear height control sensor sub-assembly

·

Harness or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

E223762E25
0.729,2.771 2.458,3.156 1.729,0.385 10 false Rear Height Control Sensor Sub-assembly 1.656,2.188 2.083,2.354 0.427,0.167 10 false SHB 1.552,0.833 2.385,1.26 0.833,0.427 10 false SHRR 1.635,1.542 2.302,1.927 0.667,0.385 10 false SHG 5.031,2.156 6.073,2.885 1.042,0.729 10 false SBR 5.031,0.844 5.813,1.281 0.781,0.438 10 false SHRL 5.042,1.49 5.75,1.833 0.708,0.344 10 false SGR 4.938,2.823 6.438,3.219 1.5,0.396 10 false Headlight Leveling ECU Assembly 4.75,2.094 4.938,2.25 0.188,0.156 10 false 12 4.75,0.75 4.938,0.906 0.188,0.156 10 false 19 4.76,1.417 4.948,1.573 0.188,0.156 10 false 21 2.073,2.083 2.219,2.24 0.146,0.156 10 false 3 2.073,0.74 2.219,0.896 0.146,0.156 10 false 2 2.063,1.427 2.229,1.583 0.167,0.156 10 false 1 4.938,2.677 5.365,2.938 0.427,0.26 10 false A82 0.74,2.635 1.01,2.802 0.271,0.167 10 false M1

CAUTION / NOTICE / HINT

NOTICE:

If either of the following is performed, initialization of the headlight leveling ECU assembly is necessary (See page Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION).

·

Replacement of the headlight leveling ECU assembly.

·

Replacement or removal/installation of the rear height control sensor sub-assembly or work that changes the vehicle height such as replacement of suspension components.



PROCEDURE

1.CHECK FOR DTC

OK

NG

2.READ VALUE USING GTS (HEIGHT SENS PW SUPPLY VAL)
2.READ VALUE USING GTS (HEIGHT SENS PW SUPPLY VAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL Auto Leveling / Data List.


e.

Read the display on the GTS.

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Height control sensor power supply value / 0.00 to 5.00 V Approx. 5 V -

OK:

Normal condition listed above is displayed.




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
a.

Remove the rear height control sensor sub-assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor sub-assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
a.

Disconnect the A82 headlight leveling ECU assembly connector.


b.

Disconnect the M1 rear height control sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A82-12 (SBR) - M1-3 (SHB) Always Below 1 Ω
A82-19 (SHRL) - M1-2 (SHRR) Always Below 1 Ω
A82-21 (SGR) - M1-1 (SHG) Always Below 1 Ω
A82-12 (SBR) or M1-3 (SHB) - Body ground Always 10 kΩ or higher
A82-19 (SHRL) or M1-2 (SHRR) - Body ground Always 10 kΩ or higher
A82-21 (SGR) or M1-1 (SHG) - Body ground Always 10 kΩ or higher




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR