Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0248287 CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor) Y

NETWORKING  CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

IMPORTANT POINTS CONCERNING TROUBLESHOOTING


CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Refer to the troubleshooting procedures of each system if DTCs regarding the CAN communication system are not output.

·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

*: Use the intelligent tester.



a.

DTCs indicating a CAN communication malfunction are also stored due to internal or power source-related problems in ECUs or sensors of systems using CAN communication. Therefore, check whether codes indicating internal or power source-related problems in those systems are output together with the CAN communication DTCs.


b.

It is possible to inspect the circuit of the DLC3 branch line or V bus main line for malfunctions by inspecting the terminals of the DLC3 using electrical tester.

NOTICE:

It is only possible to inspect branch lines to ECUs (sensors) or the V1 bus from the DLC3.



c.

It is possible to check which ECUs (sensors) are not able to communicate via CAN communication by checking the "Bus Check" function of the intelligent tester (when the DLC3 branch wire and V1 bus main wire are normal).

HINT:
·

When checking "Bus Check", ECUs (sensors) whose branch line is open or that cannot communicate via CAN communication do not respond to the intelligent tester (they are not displayed on the screen).

·

When checking "Bus Check", if a DTC indicating a CAN communication malfunction is output even though all ECUs (sensors) respond (they are displayed on the screen), use the DTC combination table to determine the suspected trouble area and perform symptom simulation.




d.

For past malfunctions of the V bus, the ECUs (sensors) which cannot communicate via CAN communication can be determined from the combination of CAN communication DTCs that are output.


e.

The ECM detects malfunctions in the power train bus circuit and stores DTCs depending on the malfunctioning areas. The ECUs (sensors) which cannot communicate via CAN communication can be determined from the combination of CAN communication DTCs that are output.


f.

When an open circuit malfunction is confirmed, before disconnecting the connectors for inspection, check whether the connectors are loose by pushing in the connector case.


g.

When a connector is disconnected, check if the connector terminals or case is damaged, deformed, deteriorated, etc.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Result
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Result
NEXT



NEXT

3.CHECK AND CLEAR DTC*
3.CHECK AND CLEAR DTC*
a.

Using the intelligent tester, perform the all DTCs check.

NOTICE:
·

If codes indicating internal or power source-related malfunctions of ECUs or sensors are output together with codes indicating that those ECUs or sensors cannot communicate via CAN communication, it is likely that the problem is not in the CAN communication line. Therefore, perform troubleshooting for the DTCs related to the malfunctioning parts first.

·

If a connector of a system which includes a CAN communication line is disconnected when the ignition switch is ON or ACC, CAN communication DTCs will be stored by that system and any related systems.




Result:
Result
NEXT



NEXT

4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM


Result:
Result
NEXT



NEXT

5.CHECK FOR OPEN CIRCUIT IN DLC3 BRANCH WIRE AND V BUS CIRCUIT MAIN WIRE AND SHORT CIRCUIT (CANH - CANL)
5.CHECK FOR OPEN CIRCUIT IN DLC3 BRANCH WIRE AND V BUS CIRCUIT MAIN WIRE AND SHORT CIRCUIT (CANH - CANL)
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.


b.
C152423C70
1.5,0.208 1.885,0.438 0.385,0.229 1.625,1.885 1.958,1.469 true 1.958,0.917 2.292,0.5 true 0.271,0.146 0.479,0.344 0.208,0.198 10 false *a 1.625,0.24 1.833,0.438 0.208,0.198 10 false F4 1.229,1.802 1.677,2.021 0.448,0.219 10 false CANL 2.333,0.354 2.781,0.573 0.448,0.219 10 false CANH
*a Front view of DLC3


Measure the resistance of the DLC3.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F4-6 (CANH) - F4-14 (CANL) Ignition switch off 54 to 69 Ω



Result:
Result Proceed to
OK (54 to 69 Ω) A
NG (Higher than 70 Ω) B
NG (Below 54 Ω) C



A

6.CHECK FOR SHORT TO +B IN CAN V BUS (CANH, CANL - BAT)

B

C

6.CHECK FOR SHORT TO +B IN CAN V BUS (CANH, CANL - BAT)
a.
C152423C71
1.479,0.24 1.865,0.458 0.385,0.219 1.688,1.854 1.958,1.448 true 1.958,0.927 2.229,0.521 true 2.698,1.865 2.333,1.469 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.583,0.26 1.885,0.458 0.302,0.198 10 false F4 2.26,0.375 2.719,0.552 0.458,0.177 10 false CANH 1.323,1.792 1.74,1.958 0.417,0.167 10 false CANL 2.75,1.781 3.167,1.948 0.417,0.167 10 false BAT
*a Front view of DLC3


Measure the resistance of the DLC3.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F4-6 (CANH) - F4-16 (BAT) Ignition switch off 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) Ignition switch off 6 kΩ or higher



Result:
Result
OK
NG



OK

7.CHECK FOR SHORT TO GND IN CAN V BUS (CANH, CANL - CG)

NG

7.CHECK FOR SHORT TO GND IN CAN V BUS (CANH, CANL - CG)
a.
C152423C72
1.479,0.24 1.865,0.458 0.385,0.219 1.688,1.854 1.958,1.448 true 1.958,0.927 2.229,0.521 true 1.594,0.917 1.25,0.5 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.583,0.26 1.885,0.458 0.302,0.198 10 false F4 2.26,0.375 2.719,0.552 0.458,0.177 10 false CANH 1.323,1.792 1.74,1.958 0.417,0.167 10 false CANL 0.99,0.396 1.313,0.573 0.323,0.177 10 false CG
*a Front view of DLC3


Measure the resistance of the DLC3.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F4-6 (CANH) - F4-4 (CG) Ignition switch off 200 Ω or higher
F4-14 (CANL) - F4-4 (CG) Ignition switch off 200 Ω or higher



Result:
Result
OK
NG



OK

8.CHECK ECUS CONNECTED TO CAN BUS*

NG

8.CHECK ECUS CONNECTED TO CAN BUS*
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Select "Bus Check" from "System Select".


c.

Check the display of the connected ECUs and sensors for a minute.

Result:
Result Proceed to
All ECUs and sensors connected to CAN communication system displayed on screen (CAN bus circuit currently normal) A
A single ECU or sensor that should be connected to CAN communication is not displayed (ECU or sensor branch wire open or communication stop) B
ECU or sensor that should be connected to CAN communication is not displayed or display is intermittent during check (ECU or sensor branch wire open on one side) C


NOTICE:

ECUs and sensors that are not present will not be displayed. Be careful not to mistake them for communication stop malfunctions.


HINT:

If the display of an ECU is intermittent during the check, one side of an ECU or sensor branch wire is open (the signal of the ECU is treated as noise, which affects the response and display of the intelligent tester).




A

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*

B

C

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*
a.

Select "Bus Check" from "System Select".


b.

Write down all of the DTCs output from each ECU.

HINT:

If there are communication malfunction DTCs output but the intelligent tester "Bus Check - Communication Bus Check" screen displays all of the ECUs and sensors connected to the CAN system, the communication malfunction DTCs may be past malfunctions that are no longer present.



Result:
Result
NEXT



NEXT

10.CHECK DTC COMBINATION TABLE (V BUS BRANCH WIRE OPEN, PAST COMMUNICATION STOP MALFUNCTION)
10.CHECK DTC COMBINATION TABLE (V BUS BRANCH WIRE OPEN, PAST COMMUNICATION STOP MALFUNCTION)
a.

Based on the combination of output CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for Separate Type Yaw Rate Sensor)>DIAGNOSIS SYSTEM


Result:
Result
NEXT



NEXT

11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)*
11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT MAIN WIRE PAST MALFUNCTION)*
a.

Using the intelligent tester, clear all DTCs.


b.

Perform a malfunction simulation test on all harnesses and connectors related to the V1 bus main wire.


c.

Check the DTCs that were output as a result of the malfunction simulation test. Then determine the malfunctioning area.


Result:
Proceed to
NEXT



NEXT

12.ADJUST, REPAIR AND REPLACE
12.ADJUST, REPAIR AND REPLACE
Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC*
13.CLEAR DTC*
a.

Using the intelligent tester, clear all DTCs.


Result:
Proceed to
NEXT



NEXT

14.CONFIRMATION TEST
14.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END