Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.09
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705 one of the following conditions (A), (B) or (C) is met:
·

Wire harness or connector

·

Park/neutral position switch

·

Shift lock control unit assembly (Transmission control switch)

·

ECM


Condition (A):
Any 2 or more of the following signals are on simultaneously (2 trip detection logic).
·

one of the following conditions is met.

P input signal is on.

N input signal is on.

NSW input signal is on.

·

R input signal is on.

·

D input signal is on.

·

2 input signal is on.

·

L input signal is on.


Condition (B):
All switches are off simultaneously (2 trip detection logic).
·

P input signal is off.

·

N input signal is off.

·

NSW input signal is off.

·

R input signal is off.

·

D input signal is off.

·

2 input signal is off.

·

L input signal is off.


Condition (C):
When any of following conditions is met, the 3 position input signal is on for 2 seconds or more (2 trip detection logic).
·

NSW input signal is on.

·

P input signal is on.

·

R input signal is on.

·

N input signal is on.

·

2 input signal is on.

·

L input signal is on.



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives 2 or more position signals simultaneously or it receives no position signal. The ECM turns on the MIL and stores the DTC.

WIRING DIAGRAM

C291947E03
0.177,0.646 0.948,0.792 0.771,0.146 10 false to ST Relay 0.448,2.281 0.99,2.438 0.542,0.156 10 false GAUGE 1.563,0.573 1.667,0.719 0.104,0.146 10 false 5 1.75,0.573 1.854,0.719 0.104,0.146 10 false L 2.927,0.573 3.031,0.719 0.104,0.146 10 false 4 2.74,0.573 2.854,0.719 0.115,0.146 10 false B 2.927,1.135 3.031,1.281 0.104,0.146 10 false 6 2.656,1.135 2.865,1.281 0.208,0.146 10 false PL 2.927,1.5 3.031,1.646 0.104,0.146 10 false 1 2.656,1.5 2.865,1.646 0.208,0.146 10 false RL 2.927,1.875 3.031,2.021 0.104,0.146 10 false 9 2.656,1.875 2.865,2.021 0.208,0.146 10 false NL 2.927,2.25 3.031,2.396 0.104,0.146 10 false 7 2.656,2.25 2.865,2.396 0.208,0.146 10 false DL 2.927,2.635 3.031,2.781 0.104,0.146 10 false 3 2.656,2.635 2.865,2.781 0.208,0.146 10 false 2L 2.927,3 3.031,3.146 0.104,0.146 10 false 8 2.656,3 2.865,3.146 0.208,0.146 10 false LL 1.417,3.417 1.698,3.573 0.281,0.156 10 false B88 1.417,3.563 3.271,3.76 1.854,0.198 10 false Park/Neutral Position Switch 1.563,2.073 1.667,2.219 0.104,0.146 10 false 2 1.729,2.073 2.01,2.219 0.281,0.146 10 false RB 1.563,4.302 1.667,4.469 0.104,0.167 10 false 1 1.74,4.302 2.146,4.448 0.406,0.146 10 false NSSD 2.917,4.302 3.021,4.469 0.104,0.167 10 false 2 2.594,4.302 2.865,4.448 0.271,0.146 10 false AT3 1.229,4.792 1.625,4.948 0.396,0.156 10 false F25 1.229,4.969 3.271,5.281 2.042,0.313 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 5.417,0.646 5.698,0.792 0.281,0.146 10 false B89 5.469,0.469 5.646,0.604 0.177,0.135 10 false 63 5.771,0.646 6.135,0.792 0.365,0.146 10 false NSW 5.417,1.198 5.698,1.344 0.281,0.146 10 false B89 5.469,1.01 5.646,1.146 0.177,0.135 10 false 99 5.771,1.198 6.135,1.344 0.365,0.146 10 false P 5.417,1.583 5.698,1.729 0.281,0.146 10 false B89 5.469,1.406 5.646,1.542 0.177,0.135 10 false 79 5.771,1.583 6.135,1.729 0.365,0.146 10 false R 5.417,1.969 5.698,2.115 0.281,0.146 10 false B89 5.469,1.781 5.646,1.917 0.177,0.135 10 false 97 5.771,1.969 6.135,2.115 0.365,0.146 10 false N 5.427,2.333 5.708,2.479 0.281,0.146 10 false B89 5.469,2.146 5.646,2.281 0.177,0.135 10 false 81 5.406,2.542 5.646,2.688 0.24,0.146 10 false 131 5.469,2.917 5.646,3.052 0.177,0.135 10 false 98 5.771,2.333 6.135,2.479 0.365,0.146 10 false D 5.417,2.719 5.698,2.865 0.281,0.146 10 false B89 5.771,2.719 6.135,2.865 0.365,0.146 10 false 2 5.417,3.104 5.698,3.25 0.281,0.146 10 false B89 5.771,3.104 6.135,3.25 0.365,0.146 10 false L 5.469,4.208 5.646,4.344 0.177,0.135 10 false 58 5.417,4.385 5.698,4.531 0.281,0.146 10 false A83 5.771,4.385 6.135,4.531 0.365,0.146 10 false 3 6.125,4.844 6.5,5.01 0.375,0.167 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


f.

According to the display on the GTS, read the Data List.



Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch Status/
OFF or ON
·

OFF: Shift lever not in P and N

·

ON: Shift lever in P or N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (R Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


Shift SW Status (P Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


Shift SW Status (N Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


Shift SW Status (D Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in D

·

ON: Shift lever in D


Shift SW Status (3 Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in 3

·

ON: Shift lever in 3


Shift SW Status (2 Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in 2

·

ON: Shift lever in 2


Shift SW Status (L Range) PNP switch Status/
OFF or ON
·

OFF: Shift lever not in L

·

ON: Shift lever in L



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH)
a.
U158510E04
1.854,0.958 2.365,0.458 true 2.438,0.344 2.688,0.542 0.25,0.198 10 false RB 0.198,0.021 0.438,0.188 0.24,0.167 10 false *a 0.229,1 0.583,1.167 0.354,0.167 10 false B88

Disconnect the park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B88-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
U158511E04
2.208,0.958 2.417,0.438 true 2.458,0.313 2.708,0.51 0.25,0.198 10 false B 0.156,0.063 0.396,0.229 0.24,0.167 10 false *a 0.24,1.01 0.604,1.188 0.365,0.177 10 false B88

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B88-4 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C193931E48
0.906,0.365 1.354,0.958 true 0.552,0.667 1.146,0.958 true 0.948,1.844 1.26,1.5 true 1.344,1.844 1.448,1.5 true 1.729,1.854 1.792,1.49 true 2.542,1.833 2.323,1.49 true 1.917,0.25 1.615,0.958 true 2.563,0.615 1.969,0.979 true 2.083,1.875 2.146,1.51 true 0.083,0.073 0.271,0.25 0.188,0.177 10 false *a 0.698,0.219 0.917,0.375 0.219,0.156 10 false 2L 0.417,0.5 0.552,0.656 0.135,0.156 10 false B 0.688,1.813 0.906,1.969 0.219,0.156 10 false NL 1.656,1.885 1.875,2.042 0.219,0.156 10 false DL 2.021,1.906 2.24,2.063 0.219,0.156 10 false PL 2.677,1.792 2.802,1.948 0.125,0.156 10 false L 1.99,0.115 2.25,0.271 0.26,0.156 10 false RB 2.646,0.521 2.865,0.677 0.219,0.156 10 false RL 1.24,1.875 1.458,2.031 0.219,0.156 10 false LL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever in D or 3 Below 1 Ω
Shift lever not in D and 3 10 kΩ or higher
2 (RB) - 3 (2L) Shift lever in 2 Below 1 Ω
Shift lever not in 2 10 kΩ or higher
2 (RB) - 8 (LL) Shift lever in L Below 1 Ω
Shift lever not in L 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch)



OK

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C193928E18
0.12,0.035 0.300,0.201 0.180,0.166 10 *a 2.851,0.987 3.270,1.156 0.419,0.170 10 NSSD 1.081,0.099 1.363,0.268 0.282,0.170 10 AT3 1.408,0.189 2.076,0.982 false 2.294,1.043 2.807,1.083 false

Disconnect the F25 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NSSD) - 2 (AT3) Shift lever in 3 Below 1 Ω
Shift lever not in 3 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TRANSMISSION CONTROL SWITCH)
a.
U158327E02
0.792,0.563 1.135,1.094 true 0.083,0.052 0.271,0.229 0.188,0.177 10 false *a 0.406,0.958 0.677,1.115 0.271,0.156 10 false F25 0.323,0.469 0.719,0.635 0.396,0.167 10 false NSSD

Connect the B88 park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F25-1 (NSSD) - Body ground Ignition switch ON
Shift lever in D or 3
11 to 14 V
Ignition switch ON
Shift lever not in D and 3
Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))



OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C361140E01
2.667,1.208 2.167,1.833 false 0.24,0.948 0.698,1.146 0.458,0.198 10 false A83 2.115,1.875 2.271,2.073 0.156,0.198 10 false 3 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a

Connect the F25 transmission control switch connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A83-58 (3) - Body ground Ignition switch ON
Shift lever in 3
11 to 14 V
Ignition switch ON
Shift lever not in 3
Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
C361141E01
1.969,1.167 2.667,0.333 true 0.677,1.167 0.333,1.833 true 1.844,1.156 2.25,0.333 true 0.802,1.167 1.083,0.417 true 1.958,1.219 2.25,1.833 true 1.906,1.167 1.667,1.833 true 1.552,0.229 2.01,0.427 0.458,0.198 10 false B89 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 2.688,0.156 2.844,0.354 0.156,0.198 10 false P 0.26,1.885 0.417,2.083 0.156,0.198 10 false R 2.26,0.167 2.417,0.365 0.156,0.198 10 false N 1.063,0.177 1.219,0.375 0.156,0.198 10 false D 2.219,1.875 2.375,2.073 0.156,0.198 10 false 2 1.604,1.885 1.76,2.083 0.156,0.198 10 false L

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B89-99 (P) - Body ground Ignition switch ON
Shift lever in P
11 to 14 V
Ignition switch ON
Shift lever not in P
Below 1 V
B89-79 (R) - Body ground Ignition switch ON
Shift lever R
11 to 14 V*
Ignition switch ON
Shift lever not in R
Below 1 V
B89-97 (N) - Body ground Ignition switch ON
Shift lever in N
11 to 14 V
Ignition switch ON
Shift lever not in N
Below 1 V
B89-81 (D) - Body ground Ignition switch ON
Shift lever in D or 3
11 to 14 V
Ignition switch ON
Shift lever not in D and 3
Below 1 V
B89-131 (2) - Body ground Ignition switch ON
Shift lever in 2
11 to 14 V
Ignition switch ON
Shift lever not in 2
Below 1 V
B89-98 (L) - Body ground Ignition switch ON
Shift lever in L
11 to 14 V
Ignition switch ON
Shift lever not in L
Below 1 V


HINT:

*: The voltage will drop slightly due to the back up light being turned on.


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the B89 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-63 (NSW) - B88-4 (B) Always Below 1 Ω
B88-4 (B) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR