Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.09
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

Refer to P2714 (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>P2714).

DTC No. DTC Detection Condition Trouble Area
P2716 Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detecting logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve SLT

·

ECM



MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the ECM interprets this as a fault. The ECM turns on the MIL and stores the DTC.

WIRING DIAGRAM

C361151E01
1.083,2.219 1.542,2.417 0.458,0.198 10 false B74 1.083,2.406 3.688,2.604 2.604,0.198 10 false Transmission Wire 1.313,1 2.208,1.521 0.896,0.521 10 false Shift Solenoid Valve SLT 2.177,0.563 2.792,0.76 0.615,0.198 10 false SLT+ 2.177,1.521 2.792,1.719 0.615,0.198 10 false SLT- 2.76,0.552 2.917,0.75 0.156,0.198 10 false 3 2.76,1.542 2.917,1.74 0.156,0.198 10 false 8 5.813,0.698 6.427,0.896 0.615,0.198 10 false SLT+ 5.844,1.677 6.302,1.875 0.458,0.198 10 false SLT- 5.5,0.573 5.813,0.771 0.313,0.198 10 false 73 5.5,1.542 5.813,1.74 0.313,0.198 10 false 72 6.01,2.198 6.469,2.396 0.458,0.198 10 false B89 6,2.396 6.458,2.594 0.458,0.198 10 false ECM

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
C229166E09
2.132,0.42 2.530,0.579 0.398,0.158 10 SLT+ 1.442,1.837 1.834,1.998 0.392,0.161 10 SLT- 1.757,0.917 2.091,0.51 false 1.775,1.24 1.63,1.783 false 0.059,0.028 0.256,0.192 0.197,0.164 10 *a

a.

Disconnect the B74 transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SLT+) - 8 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
3 (SLT+) - Body ground Always 10 kΩ or higher
8 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
C361141E07
1.198,1.104 0.667,1.833 true 1.271,1.094 1.844,1.813 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.552,0.219 2.01,0.417 0.458,0.198 10 false B89 0.542,1.885 1.156,2.083 0.615,0.198 10 false SLT- 1.771,1.875 2.385,2.073 0.615,0.198 10 false SLT+

a.

Connect the B74 transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-73 (SLT+) - B89-72 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
B89-73 (SLT+) - Body ground Always 10 kΩ or higher
B89-72 (SLT-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR