Home › Drivetrain › U340E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2014.07
RM19S0E _52 Drivetrain _051465 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0248156 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2714  Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)  


DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

C233512E01
1.021,0.51 2.116,0.837 1.095,0.327 10 Line Pressure Control Pressure 2.037,1.523 3.591,1.678 1.554,0.156 10 Current Flow to Solenoid 4.084,0.217 4.853,0.364 0.769,0.147 10 Spool Valve 4.809,1.377 5.264,1.525 0.455,0.148 10 Sleeve 5.545,1.526 6.398,1.678 0.853,0.152 10 Solenoid Coil 4.843,0.304 5.048,0.731 false 5.024,1.377 5.254,0.932 false 6.3,0.52 5.95,1.498 5.95,1.498 6.313,0.959 false

DTC No. DTC Detection Condition Trouble Area
P2714 ECM detects malfunction on SLT (ON side) according to difference in revolutions of turbine (input) and output shaft (2 trip detection logic).
·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked

·

Torque converter assembly

·

Automatic transaxle (clutch, brake or gear etc.)

·

Shift solenoid valve SLT



MONITOR DESCRIPTION

In any forward position, when the difference between the revolutions of the turbine and output shaft exceeds the specified value (varies with output speed) determined by the ECM, the ECM illuminates the MIL and stores the DTC. When shift solenoid valve SLT remains on, the oil pressure goes down and the clutch engagement force decreases.

CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

In accordance with the display on the tester, perform the Active Test.

Tester Display Test Part Control Range Diagnostic Note
Activate the Solenoid (SLT)* [Test Details]
Operate shift solenoid SLT and raise line pressure.
HINT:

OFF: Line pressure up (when active test of Solenoid (SLT) is performed, ECM turns off SLT solenoid)

ON: No action (normal operation)


ON/OFF [Vehicle Condition]
·

Vehicle Stopped

·

Shift lever in P or N

·

Vehicle speed sensor normal

·

Accelerator pedal is released



*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the Hydraulic Test (See page Drivetrain>U340E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST) as well.

HINT:

The pressure values in Active Test and Hydraulic Test are different from each other.




PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
Only P2714 is output A
P2714 and other DTCs are output B

HINT:

If any other DTCs besides P2714 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SLT

B

2.INSPECT SHIFT SOLENOID VALVE SLT
C204845E10
0.938,0.813 1.531,1.083 true 1.896,1.083 2.458,0.823 true 0.969,2.948 1.542,3.198 true 1.885,3.188 2.438,2.958 true 0.073,0.063 0.323,0.25 0.25,0.188 10 false *a 0.823,0.708 0.927,0.875 0.104,0.167 10 false 1 2.51,0.74 2.615,0.906 0.104,0.167 10 false 2 0.865,2.865 0.969,3.031 0.104,0.167 10 false 1 2.49,2.885 2.594,3.052 0.104,0.167 10 false 2 2.875,3.573 3.25,3.74 0.375,0.167 10 false 21 W

a.

Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

OK:

The solenoid makes operating sounds.


Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SLT)



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG