Home › Engine / Hybrid System › 2NZ-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2016.09
RM19S0E _51 Engine / Hybrid System _051457 2NZ-FE INTAKE / EXHAUST _0248116 EXHAUST MANIFOLD A

2NZ-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17173 1.INSTALL EXHAUST MANIFOLD TO HEAD GASKET

a.

Remove the exhaust manifold to head gasket from the cylinder head assembly.


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.
U134149E03
1.667,0.042 1.823,0.208 0.156,0.167 10 true 1 1.052,1.104 1.146,1.25 0.094,0.146 10 false 2 2.281,1.083 2.375,1.229 0.094,0.146 10 false 3 0.396,0.688 0.49,0.833 0.094,0.146 10 false 4 2.979,0.656 3.104,0.833 0.125,0.177 10 false 5

Install the exhaust manifold with the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 25591 3.INSTALL MANIFOLD SUPPORT BRACKET

a.

Install the manifold support bracket with the 3 bolts.

Torque:
44 N*m (449 kgf*cm, 33 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the wire harness bracket with the bolt.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


c.

Engage the 2 wire harness clamps and install the wire harness.


Hide 12363A 5.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod with the bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 17451 6.INSTALL EXHAUST PIPE GASKET

a.
A128852E06
2.031,1.135 1.844,1.385 false 1.833,0.979 1.594,1.604 false 2.292,1.521 2.104,1.771 false 0.771,2.479 1.146,2.177 false 2.052,1.01 2.26,1.188 0.208,0.177 10 false *2 1.781,0.813 1.99,0.99 0.208,0.177 10 false *1 2.323,1.396 2.531,1.573 0.208,0.177 10 false *3 0.583,2.417 0.792,2.594 0.208,0.177 10 false *4

Using a plastic hammer and a wooden block, tap in a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

Text in Illustration
*1 Exhaust Pipe Gasket
*2 Wooden Block
*3 Plastic Hammer
*4 Exhaust Manifold

NOTICE:
·

Install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket by dropping it, etc.

·

Do not damage the outer surface of the gasket.

·

Do not push in the gasket with the exhaust pipe when connecting it.




Hide 17451A 7.INSTALL NO. 2 EXHAUST PIPE GASKET

a.
A128852E06
2.031,1.135 1.844,1.385 false 1.833,0.979 1.594,1.604 false 2.292,1.521 2.104,1.771 false 0.771,2.479 1.146,2.177 false 2.052,1.01 2.26,1.188 0.208,0.177 10 false *2 1.781,0.813 1.99,0.99 0.208,0.177 10 false *1 2.323,1.396 2.531,1.573 0.208,0.177 10 false *3 0.583,2.417 0.792,2.594 0.208,0.177 10 false *4

Install the No. 2 exhaust pipe gasket to the front exhaust pipe assembly.

Text in Illustration
*1 No. 2 Exhaust Pipe Gasket
*2 Wooden Block
*3 Plastic Hammer
*4 Front Exhaust Pipe Assembly


Hide 17410 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum Length:

41.5 mm (1.634 in.)


If the length is not as specified, replace the compression spring.


b.

Hang the front exhaust pipe assembly with the 3 exhaust pipe supports.


c.
A247549E04
0.271,0.521 0.542,0.667 false 0.281,0.958 0.531,0.896 false 1.958,0.979 2.125,1.229 true 0.115,0.438 0.281,0.656 0.167,0.219 10 false *1 0.115,0.896 0.281,1.104 0.167,0.208 10 false *2 2.063,1.24 2.219,1.438 0.156,0.198 10 false *3 2.75,1.344 2.958,1.594 0.208,0.25 10 false *a

Install the front exhaust pipe sub-assembly onto the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.

Text in Illustration
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Gasket
*a Space between flanges: 8.5 mm (0.335 in.)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter subassembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



d.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum Length:

38.5 mm (1.516 in.)


HINT:

If the length is not as specified, replace the compression spring.



e.
A247551E04
2.635,1.104 2.948,1.063 false 2.625,1.333 2.917,1.396 false 1.458,1.365 1.375,1.594 false 0.469,0.625 0.625,0.771 0.156,0.146 10 false *a 2.979,0.958 3.156,1.167 0.177,0.208 10 false *1 2.958,1.333 3.146,1.531 0.188,0.198 10 false *2 1.25,1.594 1.406,1.74 0.156,0.146 10 false *3

Connect the tail exhaust pipe assembly onto the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 No. 2 Exhaust Pipe Gasket
*a Space between flanges: 6.5 mm (0.256 in.)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After the installation, check that the gaps between the flanges of the exhaust manifold converter subassembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



f.

Pass the connector through the hole into the inside of the vehicle and install the oxygen sensor wire grommet.


g.

Connect the oxygen sensor connector.


Hide 57533B 9.INSTALL FRONT FLOOR CENTER BRACE

a.

Install the front floor center brace to the vehicle with the 4 bolts.

Torque:
30 N*m (307 kgf*cm, 22 ft.*lbf)


Hide 58910C 10.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 12.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION