This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B2799 | Either condition is met (1 trip detection logic*):
·
A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. ·
A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. |
·
Harness or connector ·
Transponder key ECU assembly ·
ECM |
Either condition is met:
·
Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds). ·
10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds). |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC Code | Data List and Active Test |
|---|---|
| B2799 | - |
When replacing the transponder key ECU assembly, refer to the Service Bulletin.
When replacing the ECM, refer to the INITIALIZATION (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
Clear the DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).
NEXT
Start the engine.
Wait 10 seconds or more.
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B2799 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B2799 is output) | B |
| NG (Other DTCs are output) | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECU) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | A83-29 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected. |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Terminal IMO stuck low (2.4 V or less) | B |
| Terminal IMO stuck high (12 V) or Abnormal waveform | C |
A
B
C
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECU) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | A83-28 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected. |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Not output waveform or abnormal waveform | B |
A
B
Reregister the ECU communication ID (Refer to Service Bulletin).
NEXT
Check that the engine starts with an already registered vehicle key.
Engine starts normally.
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the A83 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Result | Proceed to |
|---|---|
| Terminal IMO stuck low (2.4 V or less) | A |
| Terminal IMO stuck high (12 V) | B |
A
B
Disconnect the F54 transponder key ECU assembly connector.
Disconnect the A83 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F54-12 (EFII) - A83-29 (IMO) | Always | Below 1 Ω |
| F54-12 (EFII) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the transponder key ECU assembly (Refer to Service Bulletin).
NEXT
Reregister the key (Refer to Service Bulletin).
NEXT
Reregister the ECU communication ID (Refer to Service Bulletin).
NEXT
Check that the engine starts with an already registered vehicle key.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2NZ-FE) | B |
| NG (for 1NZ-FE) | C |
A
B
C
Temporarily replace the ECM with a new one.
for 2NZ-FE (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>ECM>REMOVAL).
for 1NZ-FE (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>ECM>REMOVAL).
NEXT
Reregister the ECU communication ID (Refer to Service Bulletin).
NEXT
Check that the engine starts with the key.
Engine starts normally.
OK
NG