If the key ID codes of the key and transponder key ECU assembly match, the engine immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.
When replacing the key and transponder key ECU assembly, refer to the Service Bulletin.
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Result | Proceed to |
|---|---|
| No DTC output | A |
| DTC output | B |
A
B
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Stored as Freeze Frame Data |
|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser fuel cut / OFF or ON | - | Yes |
The item in the Data List indicates "OFF"
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 1NZ-FE) | B |
| OK (for 2NZ-FE) | C |
A
B
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
(See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
It leaves for 5 seconds by the ignition switch ON status, and the engine starting operation is done.
| Result | Proceed to |
|---|---|
| Engine cannot be started | A |
| Engine can be started | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Waveform A |
| Item | Content |
|---|---|
| Tester Connection | A83-28 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform 1 or 2 (Waveform A) not output, or has abnormal wavelength or shape | B |
A
B
Using an oscilloscope, check the waveform.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Waveform B |
| *e | 160 ms | *f | 510 ms |
| *g | 270 ms | - | - |
| Item | Content |
|---|---|
| Tester Connection | A83-29 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 1NZ-FE) | B |
| Waveform 1 or 2 (Waveform B) not output, or has abnormal wavelength or shape (for 2NZ-FE) | C |
A
B
C
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Waveform C |
| *e | 160 ms | *f | 510 ms |
| *g | 270 ms | - | - |
| Item | Content |
|---|---|
| Tester Connection | A83-28 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected |
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform 1 or 2 (Waveform C) not output, or has abnormal wavelength or shape | B |
A
B
Register the ECU communication ID (Refer to Service Bulletin).
NEXT
Check that the engine starts with the key.
Engine starts normally.
OK
NG
Disconnect the A83 ECM connector.
Disconnect the F54 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-28 (IMI) - F54-13 (EFIO) | Always | Below 1 Ω |
| A83-28 (IMI) or F54-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the transponder key ECU assembly with a new one (Refer to Service Bulletin).
Check that the engine starts with the key.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE) | B |
| NG (for 2NZ-FE) | C |
A
B
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
(See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)