To control the cooling fans, the ECM turns on or off the cooling fan relays based on the engine coolant temperature, air conditioning switch, refrigerant pressure, engine speed and vehicle speed signals.
The ECM turns on or off the fan relays to switch the cooling fan motor circuit between the series circuit and parallel circuit, controlling the cooling fan motor speed in 2 steps.
Refer to System Diagram (See page Engine / Hybrid System>1NZ-FE COOLING>COOLING FAN SYSTEM>SYSTEM DIAGRAM).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Remove the FAN No. 1 relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FAN No. 1 relay holder 3 - Body ground | Always | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | FAN No. 1 Relay Holder |
Reinstall the FAN No. 1 relay.
OK
NG
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.
Turn the Ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| FAN No. 1 relay holder 1 - Body ground | Ignition switch ON | 11 to 14 V |
| FAN No. 2 relay holder 2 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | FAN No. 1 Relay Holder |
| *3 | FAN No. 2 Relay Holder |
Reinstall the FAN No. 1 relay and FAN No. 2 relay.
OK
NG
Inspect the FAN No. 1 relay (See page Engine / Hybrid System>1NZ-FE COOLING>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Inspect the FAN No. 2 relay (See page Engine / Hybrid System>1NZ-FE COOLING>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Inspect the cooling fan resistor (See page Engine / Hybrid System>1NZ-FE COOLING>COOLING FAN RESISTOR>ON-VEHICLE INSPECTION).
OK
NG
Remove the FAN No. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FAN No. 2 relay holder 5 - Body ground | Always | Below 1 Ω |
Reinstall the FAN No. 2 relay.
OK
NG
Disconnect the cooling fan resistor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A22-1 (-) - Body ground | Always | Below 1 Ω |
Connect the cooling fan resistor connector.
OK
NG
Disconnect the cooling fan resistor connector.
Remove the FAN No. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FAN No. 2 relay holder 4 - A22-2 (+) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A22-2 (+) or FAN No. 2 relay holder 4 - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay.
Reconnect the cooling fan resistor connector.
OK
NG
Inspect the cooling fan motor (See page Engine / Hybrid System>1NZ-FE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the cooling fan motor connector.
Remove the FAN No. 1 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-2 - FAN No. 1 relay holder 5 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-2 or FAN No. 1 relay holder 5 - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 1 relay.
Reconnect the cooling fan motor connector.
OK
NG
Disconnect the cooling fan motor connector.
Remove the FAN No. 2 relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-1 - FAN No. 2 relay holder 3 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-1 or FAN No. 2 relay holder 3 - Body ground | Always | 10 kΩ or higher |
Reinstall the FAN No. 2 relay.
Reconnect the cooling fan motor connector.
OK
NG
Remove the FAN No. 1 relay and FAN No. 2 relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-8 (FANH) - FAN No. 2 relay holder 1 | Always | Below 1 Ω |
| A83-7 (FANL) - FAN No. 1 relay holder 2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A83-8 (FANH) or FAN No. 2 relay holder 1 - Body ground | Always | 10 kΩ or higher |
| A83-7 (FANL) or FAN No. 1 relay holder 2 - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reinstall the FAN No. 1 relay and FAN No. 2 relay.
OK
NG